Many people have been confused recently about the annual vehicle inspection requirements (***25 items) in Jiangmen and have been consulting the editor. Today, the editor of Pacific Automotive Network has sorted out the following content regarding this issue. , I hope it can help you answer your questions.

Main requirements for passing the inspection of high-speed trains

Serial number

Items

Qualification requirements

Vehicle identification number (complete vehicle Factory number

)

Cars, motorcycles, semi-trailers and center-axle trailers shipped from the factory on September 1, 2012 should have a unique vehicle identification number, and there should be at least one The vehicle identification number is engraved on the frame (motor vehicles without a frame are the main parts of the body that cannot be disassembled) to prevent rust and wear. Passenger cars and vehicles with a total mass less than Trucks weighing 3,500kg (except low-speed vehicles) should also be equipped with a vehicle identification number mark that can be permanently maintained and clearly readable from outside the vehicle near the windshield pillar; other motor vehicles should be engraved with the vehicle model and factory serial number. , the model number is in the front, and the factory number is in the back. Start and end marks should be engraved on both ends of the factory number. Low-speed vehicles shipped from the factory starting from April 1, 2007, should be engraved with vehicle identification numbers in accordance with regulations.

It is not allowed to have the vehicle identification number, vehicle model number and factory serial number stamped on the same vehicle. All vehicle identification numbers (or vehicle factory numbers, the same below) marked on the same vehicle should have the same content. Modified cars shipped before October 1, 2004 may have two vehicle identification numbers with different contents. In this case, one vehicle identification number should have the same content as the relevant certificate.

The engraved vehicle identification number should be easy to see and easy to rub. Its content should be recorded and integrated with the relevant certificates (motor vehicle factory qualification certificate, cargo import certificate or "motor vehicle driving license"). The vehicle identification number indicated on the vehicle product label must be consistent, and there should be no obvious changes, modifications, chiseling, digging, grinding marks or gaskets, or unauthorized additional engraving and other abnormal circumstances. For cars, motorcycles, semi-trailers and center-axle trailers manufactured since September 1, 2014, the engraved vehicle identification number should not be covered by any surface that is large enough around the engraved area when viewed from the top (front). If there is a covering, the surface of the covering should be clearly marked with the words "Vehicle Identification Number" or "VIN", and the covering can be directly removed (or uncovered) and restored without using any special tools.

Engine (electric motor) model and factory number

The engine model and factory number should be engraved (or cast) on the cylinder block and should be permanently maintained; the engraved engine should be left factory The serial number should not have any obvious signs of chiseling, digging, polishing, or unauthorized additional engraving or any other abnormality. If the engraved (or cast) engine model number and factory number are not easily visible, a permanently maintained logo of the engine model number and factory number should be added to an easily visible part of the engine.

Pure electric vehicles, plug-in hybrid vehicles, fuel cell vehicles and electric motorcycles shipped from the factory on March 1, 2013, the motor model and number should be engraved on the main drive motor casing; If the engraved motor model and number are covered, an observation opening should be left, or a logo of the motor model and number should be permanently maintained on the cover.

The "engine model and factory number" recorded on the relevant certificates should be consistent with the engine model and factory number engraved or cast on the engine block (or marked on the logo) and the engine model and factory number indicated on the vehicle product label. .

Note: If the engine model and factory serial number of a motor vehicle manufactured before October 1, 2004 are not easily visible, the easily visible part of the engine may not necessarily have an engine logo.

Vehicle Brand

/Model

During the registration inspection, the complete motor vehicle factory certificate (for domestically produced motor vehicles), the Customs Goods Import Certificate ( For imported motor vehicles), the "vehicle brand" and "vehicle model" recorded on the certificate should be consistent with the vehicle brand and model indicated on the vehicle product label.

Car body color

When registering and inspecting, the body color shall be determined according to the actual vehicle; when changing the body color, the body color shall be filled in according to the actual vehicle.

In other cases, the color of the car body should be consistent with the color of the car body recorded on the "Motor Vehicle Driving License".

Serial number

Item

Qualification requirements

Approved number of passengers

During registration inspection, follow GB7258- The approved number of passengers/cab passengers in 4.5.2~4.5.6 and 11.6 of 2012. For domestically produced motor vehicles subject to the Announcement Management, the approved number of passengers in the cab of trucks and special operation vehicles, and the approved number of passengers in passenger vehicles shall be consistent with the values ??indicated on the factory certificate of complete motor vehicles and comply with the "Announcement Management" relevant regulations. In other cases, the number of seats/berths should be consistent with the content recorded on the Motor Vehicle Driving License.

Number plate (frame)/vehicle number plate

During registration inspection, check the motor vehicle number plate (frame): front number plate (frame) (except motorcycles) ) should be located in the middle or right side of the front (according to the forward direction of the motor vehicle). The rear license plate plate (rack) should be located in the middle or left side of the rear. The license plate plate (rack) should be able to install a motor vehicle license plate that meets the requirements of GA36. . Each number plate plate (frame) of motor vehicles shipped from the factory on March 1, 2013 should be equipped with 2 number plate mounting holes. Each number plate plate (frame) of motor vehicles shipped from the factory on March 1, 2016 [ There should be 4 number plate mounting holes on the front number plate (frame) of three-wheeled vehicles and the rear number plate (frame) of motorcycles; the number plate mounting holes should ensure that M6 bolts can be used to secure the number plate directly. Reliably mounted on the vehicle.

In other cases, check the vehicle number plate: the number plate should be installed on the number plate plate (frame), the number plate should be upright, horizontally horizontal, and basically vertical vertically, and use a special sealing device that complies with GA804 When sealed, the number plate should be free of deformation, covering, damage, or alteration. The number and type of the number plate should be consistent with the records of the "Motor Vehicle Driving License." The Chinese characters, letters, and numbers should be clearly legible, and the color should have no obvious color difference. Removable number plate holders and reversible number plate holders are not permitted.

Vehicle

Appearance shape

The light-transmitting surfaces of external lighting fixtures should be complete, and the color of the light-transmitting surfaces of external lighting fixtures that are symmetrically arranged and have the same function should be different. There should be obvious differences. Rearview mirrors and lower view mirrors equipped on motor vehicles should be in good condition. All window glass should be intact and without mirror reflective sunshade film. The visible light transmittance of the front windshield and the glass other than the windshield used for the driver's viewing area should be greater than or equal to 70%. The visible light transmittance of all window glass of highway buses, tourist buses and school buses (including dedicated school buses and non-dedicated school buses) All should be greater than 50%, and no opaque or mirror-reflective colored paper or heat-insulating paper must be posted.

Trademarks, factory logos and other vehicle markings equipped on the vehicle should be consistent with the vehicle brand/model.

During registration inspection, for domestic motor vehicles subject to the "Announcement Management", the appearance and shape of the vehicle should be consistent with the photos of motor vehicles in the "Announcement, except when equipped with optional parts permitted by the Announcement; September 2012 For vans and enclosed trucks that leave the factory on January 1st, windows should be installed on both sides of the cab (area), and windows must not be installed in the cargo compartment [except for observation windows in the cab (area) used to observe the status of the cargo] . In other cases, the appearance and shape of the vehicle should be consistent with the appearance and shape of the vehicle recorded in the standard photo of the motor vehicle on the motor vehicle driving license, except when it is equipped with parts that are allowed to be installed by oneself; if the standard photo of the motor vehicle has a motor vehicle license plate, the The license plate number and type should be consistent with the content recorded on the Motor Vehicle Driving License.

Note 1: Inspectors can check standard photos of motor vehicles by collecting standard photo information of motor vehicles.

Note 2: For road buses and tourist buses manufactured before September 1, 2012, if the visible light transmittance of the side window glass is less than 50%, it will not be regarded as non-compliance with the standards.

Tires

In good condition

The tire crown pattern depth should comply with the requirements of 9.1.6 of GB7258-2012, and the tire tread and sidewall should have no impact The tire tread shall not expose the tire ply due to local wear and tear due to use of cracks, defects, abnormal wear and cuts. Tire nuts should be complete and complete. All wheels of road buses, tourist buses and school buses and steering wheels of other motor vehicles shall not be equipped with retreaded tires.

During registration inspection, the number of tires should be consistent with the data recorded in relevant certificates such as the factory certificate of motor vehicle; in other cases, the number of tires should be consistent with the data recorded in the "Motor Vehicle Standard Photo on the Motor Vehicle Driving License" The number of tires is the same.

For motor vehicles

Triangular warning signs

Cars (except three-wheeled vehicles without cabs) should be equipped with triangular warning signs for motor vehicles. It should be placed properly on the vehicle, and the style and size should comply with relevant regulations.

Car seat belts

The equipped car seat belts should be complete and functioning properly. Each berth of a sleeper coach should be equipped with a two-point safety belt.

During registration inspection, all seats of passenger cars, highway buses, tourist buses, buses without passenger standing areas, and RVs manufactured since September 1, 2012, Driver's seat and front row of other cars (except low-speed cars)

The above content is compiled and released by the editor of Pacific Automotive Network for reference. I hope it will be helpful to you. If you need more For legal answers, please consult Pacific Automotive Network online.

One million car purchase subsidies