Because the glue used for trademark labels is not resistant to high temperature, it should be baked with the warm air of a hair dryer first, and the viscosity of the trademark or seal can be torn off cleanly without leaving any traces.

Removing thinner such as alcohol, gasoline or nail polish and hand cream helps to remove these stickers easily and thoroughly. The method is to tear off a layer of paper on the surface of the label, smear it with alcohol or gasoline, then rub it on the surface by hand to make it fully saturated with adhesive, and finally wipe it off with a cloth. However, the use of these solvents may also damage the surface of the appliance. A better method is to soak the sticky part with hot water or blow it with a hair dryer, and then rub it with a wet cloth to remove the sticky matter.

How can I tear off the sticker quickly?

1. Use an eraser

Principle: Self-adhesive is fused by rubber.

Methods: Wipe with an eraser. At first, the glue will turn black, but after rubbing for a long time, the glue will slowly fall off.

Advantages: convenient operation and quick response. Disadvantages: the effect is average.

Use a hair dryer

Principle: Heat to remove the adhesive.

Methods: The hot air of electric hair dryer was used to blow each other at a distance of about 10cm from the adhesive. After blowing for a while, slowly remove the self-adhesive label while blowing.

Advantages: convenient operation, good effect and quick response.

Disadvantages: it is not suitable for heat-resistant soft plastics, and it is easy to deform objects at high temperature.

Use vinegar

Principle: Similar compatibility principle.

Method: Dip the dry dish cloth in white vinegar or vinegar, and completely cover the labeled part to make it completely soaked. After soaking 15-20 minutes, wipe off the edge of the self-adhesive label gradually with a dish cloth, and finally soak it in clear water for a while.

Advantages: it is suitable for self-adhesion on tableware and other tableware, and is non-toxic and harmless.

Disadvantages: the decontamination effect is slightly inferior.

Use edible oil

Principle: Similar compatibility principle.

Method: evenly spread the edible oil on the place where the label is attached. After 3~5 minutes, you can tear it off from the corner of the label directly by hand without leaving any label traces.

Advantages: Good decontamination effect on hard objects such as glass and stainless steel.

Disadvantages: the effect of removing glue from other objects is not good.

Step 5 use lemon juice

Principle: Similar compatibility principle.

Methods: Squeeze lemon juice on the hands with dirt, and rub it repeatedly to remove the sticky marks.

Advantages: It is suitable for removing the self-adhesive stuck on hands without causing any harm to the skin.

Disadvantages: the effect of removing glue from other objects is not good.

Use alcohol

Principle: Similar compatibility principle.

Methods: Soak the part with the self-adhesive label completely with a rag soaked in alcohol. After waiting for a period of time, wipe it slowly from the edge to the middle of the self-adhesive label with a rag soaked in alcohol until all the self-adhesive is removed.

Advantages: Good decontamination effect on hard objects such as glass and stainless steel.

Disadvantages: alcohol is not easy to get, which is harmful to the skin of the hand.

Use essential balm

Principle: Similar compatibility principle.

Methods: Soak the place with adhesive completely with wind oil essence, and dry it with a dry rag after 15 minutes. If the dirt is difficult to remove, you can extend the soaking time of the wind oil essence, and then rub it hard until it is clean.

Advantages: Almost nothing will be damaged, especially the surface of objects with printing and painting.

Disadvantages: the decontamination time is slightly longer.

Composition of adhesive:

1. Adhesive is pressure sensitive adhesive.

It is generally composed of base material, tackifying resin, active diluent and antioxidant.

According to the different substrates, there are three main types: rubber-based, polyolefin-based and acrylate polymer-based.

The tackifying resins mainly include rosin, rosin resin, terpene resin and petroleum resin.

Generally, high-grade paraffin oil with good solubility is selected as active diluent, such as KN40 10, white mineral oil, etc.

Antioxidants are mainly antioxidants.

2. According to the principle of chemical isomorphism and compatibility of polymers, the way to remove adhesives is nothing more than dissolution and anti-sticking.

Dissolution method is to dilute the self-adhesive substrate or tackifier with appropriate solvent, so that it can be easily separated from the adhered object.

The anti-sticking principle is to use the characteristics of self-adhesive components and some chemicals to prevent self-adhesion from re-bonding.

How to tear the label and uncover the sticker!

How to tear the label, how to remove the sticker? Because the sticker used for the trademark label is not resistant to high temperature, bake it with the warm air of a hair dryer first, and then the viscosity of the trademark or seal can be peeled off cleanly without leaving any traces. Removing thinner such as alcohol, gasoline or nail polish and hand cream helps to remove these stickers easily and thoroughly. The method is to tear off a layer of paper on the surface of the label, smear it with alcohol or gasoline, then rub it on the surface by hand to make it fully saturated with adhesive, and finally wipe it off with a cloth. However, the use of these solvents may also damage the surface of the appliance. A better method is to soak the sticky part with hot water or blow it with a hair dryer, and then rub it with a wet cloth to remove the sticky matter.

How to tear the tear-proof adhesive?

If the sticker on the surface is still there, you can blow it directly with a hair dryer. Soon, the sticker will float or tilt, and then you can tie the knot. If there is a black sticker on the bedside, you can apply some alcohol or gasoline on the surface and remove it later. Sticker removal trick! In practice, the following two methods are found to be good: alcohol removal method. Dip a soft cloth with 95% alcohol, and then gently wipe the adhesive, the adhesive will become soft and easy to fall off, and alcohol will generally not damage the surface of plastic parts or car paint. But sometimes it is found that alcohol is not very effective for some stickers. This can be achieved by dipping a soft cloth in a little gasoline and gently wiping the sticker. At this time, it should be noted that gasoline has a "dissolving" effect on a certain plastic or paint, so it must be used carefully: either gently wipe it in an unimportant place first and use it if there is no problem; But be careful not to use too much gasoline, as short as possible! I tried to wipe the car body surface with gasoline for a short time, but it had no obvious effect on the paint film on the car body surface. In this way, the adhesive can be easily removed ... buy a bottle of adhesive remover, and it can be used in many places as long as it is in 20 yuan. It can also be used for a long time. Tape: first scrape off the tape with a knife, and then wipe it with petroleum essence; Scrape off the adhesive tape with frosted glass and wipe it with turpentine. Try it with essential balm. Wipe with alcohol. Soak it in alcohol and it will be exposed soon. I have used alcohol and essential balm, and the effect is not good. I invented a better method. Hey, hey, I don't know if it suits your situation. That's what I usually do. It's good. Stick the adhesive tape on the indelible mark, press it with your hand and suddenly tear it off. You can paste a lot, and it will be clean after two times. . . Blessing ~ ~ I have been using essential balm, which is very useful. Drop essential balm, then rub it with your fingers, the viscose will dissolve in an instant, and then wipe it with a clean paper towel. Alcohol can remove the adhesive, and Tinea water can be used to remove the dry adhesive, which is very convenient. Try it if you don't believe me! ! ! If a cloth is not glued for a long time, it should be easy to dip it in alcohol. Just blow the glue off with a hair dryer. Using hot air oil essence will not hurt the paint surface. Very good. I used hello: you mean that the stickers on the bedside should be removed, but the bedstead is made of wood and painted; Right? Never use alcohol, thinner or other chemicals. Although these can remove the adhesive, they can also remove the paint on the bedside. Wet it with olive oil for a while and brush it with paper money. Tear off what can be torn first, and erase the rest with an eraser. You have a try. Our middle school often engages in activities, and there are many such problems and methods. Try it yourself! 1. Use alcohol! (Dilution) 2. Use an electric heater to "hot compress" (something like that)! Let those stubborn old people be hot and unbearable! 3. The "cleaning spirit" used in the kitchen-I'm not talking about this product, but something used to remove oil fumes in the kitchen. Spray it on, dip it in water with a rag later, and it will fall off as soon as it is washed. This will never hurt the paint! I promise! I tried! 4. Use "ice compress". Put ice on it until it melts. Let it get cold and lose its viscosity! Wash it with gas oil and it will be gone. All you have to do is put some wind oil on the glue and rub it. Alcohol will also remove paint while removing the adhesive, and the heat of the hair dryer will also damage the wood at the bedside when it is dry, which is not desirable. Suggest you ......

How to tear off the immovable adhesive?

(1) Wet the sign with warm water and blow it with hot air from a hair dryer for a while. The hair dryer should keep moving, and some less sticky brands can be torn off.

(2) Tear off the sticker stuck on the glass, soak the towel with hot water, wipe it repeatedly at the sticker, then soap the towel, wipe it several times at the left marks, and finally wipe the soap with a clean wet towel.

(3) Try to apply some turpentine, which can be removed in a few minutes.

(4) There are professional glue remover on the market, which is safe and easy to use.

(5) You can also use some car wash liquid, asphalt remover and multifunctional cleaning agent. Just remember never to scrape with a blade, because it is easy to scratch the glass with a blade.

If the car film sticks to the front windshield of your car, some purchased cleaning products will corrode the car film. It is best to go to a professional car beauty agency for cleaning. The specific method is as follows:

(1) Wipe it repeatedly with a towel dipped in a small amount of oil and cleaning agent, but never spray the oil and cleaning agent directly on the glass to avoid damaging the car film.

(2) There is an American rhinoceros mud on the market, which can not only clean up, but also protect the glass.

How can I tear off the back glue quickly?

Heating with a hair dryer will tear quickly and easily.

How to completely tear off the label paper stuck to the article?

1. 1. Tear off the self-adhesive decorations stuck on the surface of glass or goods, soak the towel with warm water (hot water in winter), and wipe the sticky marks twice repeatedly; Wipe the soap with a warm wet towel and rub it several times at the trace; Finally, clean the soap bubbles with a clean warm and wet towel, and the adhesion marks will be removed.

2. Apply toothpaste evenly on the adhesive surface, wait for a moment, and then wipe it with a soft rag. Sometimes it sticks more and more, and then toothpaste is applied to the traces that have not been removed at one time. The method remains the same, and the gel for headache can be removed. The principle is that toothpaste contains glycerol, which is a good solvent and can dissolve adhesive components. In addition, many cosmetics also contain glycerol, which can also be used to remove adhesives.

3. Furthermore: scrape the hard bottom surface suitable for glass, floor tiles, etc. with a pen and paper knife; Wipe with alcohol, suitable for glass, floor tiles, clothes, etc. Freezing, after freezing, the glue becomes hard and can be torn off directly, which is suitable for alcohol, scraping and other methods.

It is said that the effect of essential balm is also good. If it is a self-adhesive or the like, you can blow it with a hair dryer, which is easy to remove, but it is not suitable for plastic, and overheated plastic will be deformed.

5. Blowing heat with air duct is very effective. At home, it is convenient for everyone to have an air duct blower, which can paste glass, plastic, wood and metal. Blow a few times with the air duct first, then tear a small edge, and slowly tear it along the direction of tearing while blowing heat with the air duct, which is very effective.

How to remove the remaining glue after tearing it off?

Small bottles of washing materials sold in the hardware store.

Teach you how to deal with the residue after peeling the glue.

The first step is to tear the adhesive. You can tear it directly, but it is best to blow it with hot air from a hair dryer before tearing it, which will make it easier to tear a lot and the residue will be much less. The principle is simple. If the glue is blown soft, it will be easily torn off, especially in a large area. You can easily take off all the paint without blowing hard. I have just suffered such a loss some time ago, and usually the original paint will not have this problem. However, if I draw again, I should pay attention, because the foundation is not laid well. The disposal methods of residues are sold in auto parts cities or auto beauty shops. Face wax is the kind of spray that polishes leather. 1a bottle of 0 yuan, spray it on the residue for two or three minutes, and then wipe it with a paper towel or a dry towel. If there is a lot of residue, repeat this step. This method is suitable for all painted surfaces, glass, plastic, rubber and leather. There is also an asphalt cleaning agent, which is specially used to treat the adhesive residue on paint and glass. Auto parts cities or auto beauty shops also sell them. The price is the same as that of surface wax, and it is also a spray can. Compared with wax, the reaction speed is faster and the effect is better. It can be used when there are many residues, but it should be noted that it can only be used on paint and glass. All plastic rubber skins are finished when touched, and they are directly burned and discarded.

Stick tape on the door for a year or two; Too long to tear off; How can I tear it off?

1. Wipe it with a paper towel dipped in alcohol (preferably industrial alcohol, medical or non-medical), and it will be clean after a few wipes.

2. Use acetone. The method is as above. The dosage is small and thorough, and the best thing is that it can remove these residual gums very quickly and easily, which is better than spraying. These two solvents are the best of all methods.

3. Use nail polish remover. Usage is the same as alcohol acetone. The effect is also very good. Nail polish remover doesn't require quality, it's good and ordinary, as long as it can wash off nail polish.

4. Use hand cream. Tear off the surface print first, then squeeze some hand cream on it and rub it slowly with your thumb. After rubbing for a period of time, all the rubber residue can be wiped off. Take your time. Hand cream belongs to grease and its properties are incompatible with rubber. Glue removal is to take advantage of this feature.

Articles 3 and 4 are a column of CCTV 1