One, who meets one of the following standards, can be identified as controlled tools:
1. Dagger: a single-edged, double-edged or multi-edged sharp knife with a handle, a blade lattice and a blood groove and a blade angle of less than 60 degrees.
2. Triangle scraper: a processing tool with three blades.
3. Spring knife with self-locking device (jumping knife): a folding knife that can be fixed and self-locked by a spring or bolt in the handle after the knife body is unfolded or ejected.
4. Other similar single-edged, double-edged and triple-edged sharp knives: all kinds of single-edged, double-edged and multi-edged knives with the tip angle less than 60 degrees and the blade length exceeding150 mm..
5. Other single-edged, double-edged and multi-edged tools with a vertex angle greater than 60 degrees and a blade length greater than 220 mm..
Second, all kinds of uncut martial arts, crafts, gifts and other knives with the chamfer radius r of the tip greater than 2.5 mm do not belong to the category of controlled knives.
Three, Tibetan knives, waist knives, boots knives, shoulder knives and other knives used by ethnic minorities, the scope of control standards shall be formulated by the public security organs of the people's governments of ethnic autonomous regions (autonomous prefectures and autonomous counties) with reference to this standard.
Four. Description of predicate:
1, hilt: refers to the part of the knife used for holding.
2. Tool grid (manual stop): refers to a part of the knife, which is used to isolate the handle from the knife body.
3. Blade: refers to the part of the knife used to complete the functions of cutting, cutting and stabbing.
4. Blood groove: refers to the special groove on the knife body.
5. Tip angle: refers to the angle formed by the point on the blade and the back of the blade (or another blade) from the blade tip and the blade tip 10 mm.
6. Blade: refers to the side of the blade used for cutting, cutting and splitting. In general, the thickness of the blade is less than 0.5 mm.
7. Chamfering of the tip: refers to the radian of the tip.
Is about 25cm the length of the blade or the whole length? Is it sharp? Is the tip sharp?
According to these comprehensive judgments, we can see whether it belongs to various martial arts, crafts, gifts and other knives with uncut blades and chamfering radius r greater than 2.5 mm, in that case, it does not belong to controlled knives. It's important whether it can be opened or not.
Judging from the current standard, it is much looser than the standard of 1983.
Attached is 1983 "Interim Provisions of the Ministry of Public Security on Controlling Some Cutters".
first
In order to protect the personal safety of citizens and prevent criminals from using knives as weapons to carry out criminal activities, these Provisions are formulated.
second
These regulated knives include: daggers, triangular knives (including triangular scrapers for processing), spring knives with self-locking devices (jumping knives) and other similar single-edged, double-edged and triangular sharp knives.
essay
Dagger, in addition to the China People's Liberation Army and the people's police as weapons and police equipment, must be held by professional hunters and geological, exploration and other field workers. It must be certified by the competent unit at or above the county level, approved by the public security organ at or above the county level, and issued a "Dagger Wear Certificate" before it can be held and worn.
Whoever wears a dagger is no longer engaged in the original occupation, he shall return the dagger to the issuing unit and return the dagger wearing certificate to the original issuing public security organ.
Article 4
The triangular scraper used in processing is only used by workers in the workplace, and it is not allowed to be taken out of the workplace at will.
Article 5
Factories and workshops that manufacture knives within the above-mentioned control scope must be examined and approved by the competent authorities at or above the county level, and approved by the local county and municipal public security bureaus, and the production of special tools can only be carried out after the production license is issued. Tool samples and their descriptions (name, specification, model, use and output) should be sent to the local county and municipal public security bureau for the record. Products must be engraved with trademarks and numbers (serial numbers or batch numbers).
Article 6
Shops selling knives within the above-mentioned control range must be examined and approved by the competent department at or above the county level and approved by the local county and municipal public security bureaus. Both buyers and sellers shall establish a registration system for inspection by public security organs.
Article 7
Units and individuals who purchase controlled knives within the above-mentioned control scope must abide by the provisions of Articles 3 and 4 on possession and use. The army, police and units at or above the county level shall, with the approval of the higher authorities, order from designated units. Hunters and field workers specializing in geology and exploration should apply to the local county and municipal public security bureaus (PSBs) for the Purchase Certificate of Special Tools and purchase vouchers. Three-edged scraper, with the unit's letter of introduction to the approved dealer to buy.
Article 8
Units that use knives within the above-mentioned control scope must establish and improve the use and storage system, strengthen the management and inspection of knives, and ensure safety. Individuals who hold the above-mentioned knives shall keep them properly and shall not give them away or lend them to others at will. Found lost or stolen, should promptly report to the public security department. Where it is lost or stolen due to improper storage, resulting in serious consequences, the responsibility of the relevant personnel and unit leaders should be investigated.
Article 9
It is strictly forbidden for any unit or individual to illegally manufacture, sell and sell knives such as daggers, triangular knives and spring knives within the scope of control. It is strictly prohibited to illegally carry the above-mentioned knives into stations, docks, airports, parks, shopping malls, theaters, exhibition halls or other public places, and to take trains, cars, ships and planes.
Article 10
After the promulgation of these Provisions, all units that manufacture and sell all kinds of controlled knives within the above-mentioned control scope, professional hunters with daggers and field workers in geological exploration shall go through the registration and licensing procedures with the public security organs. If it is not necessary to hold the above-mentioned knives for production or work, it will be automatically sent to the local public security organ.
Article 11
The Special Tool Production License, the Dagger Wear Certificate and the Special Tool Purchase Certificate are uniformly stipulated by the Ministry of Public Security and printed by the public security departments and bureaus of all provinces, municipalities and autonomous regions.
Article 12
Tools that ethnic minorities need to wear because of their living habits shall be managed by ethnic autonomous areas.
Tibetan knives, waist knives and boot knives used by ethnic minorities are only allowed to be sold in ethnic autonomous areas (autonomous regions, autonomous prefectures and autonomous counties).
Article 13
Whoever, in violation of these regulations, illegally manufactures, sells, carries or hides controlled knives within the scope of control shall be banned by the public security organs, their knives shall be confiscated, and public security penalties shall be imposed in accordance with the relevant provisions of the Regulations of the People's Republic of China on Administrative Penalties for Public Security; Those who commit acts endangering public security, if the circumstances are serious and violate the criminal law, shall be investigated for criminal responsibility according to law.
Article 14
The people's governments of all provinces, municipalities and autonomous regions may formulate specific management measures according to these Provisions and report them to the Ministry of Public Security for the record.
From outdoor tools direct selling network