We often use plastic pots. Generally, there will be a trademark label at the bottom of the plastic basin. After being torn off, there is often an embarrassing situation where the glue is still on it. It feels sticky and very inconvenient to use. So how do you remove the label glue from the plastic basin? There are several ways to remove the label glue from plastic cans:
Method one
1. Prepare paper towels, white vinegar and small water cups. First, put the paper towel on the plastic basin where there is a label, pour a few drops of white vinegar into the cup, and then pour the white vinegar on the paper towel on the label.
2. Wait about 10 minutes, take away the paper towel, and gently tear off the label with your fingernail, so that the label glue can be easily dropped from the plastic basin.
Method 2
1, pour some essential balm on the plastic basin, and then wipe it in the same direction with a wet cotton cloth.
Push the glue in one direction, don't take it off in a hurry, let it stick together and then take it off directly, so that the cotton cloth won't stick.
Method 3
1. First scald the plastic basin with hot water, and then slowly scrape the glue off the plastic basin with a blunt metal tool.
2. Be careful not to scratch the plastic basin, because the plastic basin is afraid of metal. If it is scratched, it will easily lead to uneven surface of the plastic basin, so scrape it slowly.
Method 4
1. Turn on the hot air of the hair dryer. Blow the label adhesive continuously with a hair dryer.
2. When the glue on it is blown hot, the label glue will soften slowly, and it can be easily removed after blowing soft.
Method 5
Stick and tear with adhesive tape repeatedly to make the label on the plastic basin stick down.
Method 6
Cleaning with soapy water and proper amount of ammonia water will remove many impurities on it.
Method 7
Scrub sports shoes with special detergent or decontamination paste.
Generally speaking, there are many ways to remove the label glue from the plastic washbasin. If necessary, you can use it directly with reference to the above methods, but you should pay attention to using metal utensils to avoid scratching the plastic washbasin.
Second, how to remove the label glue on the stainless steel washbasin?
Stainless steel washbasin also needs to remove the label glue, but there are still some differences between stainless steel washbasin and plastic washbasin. The specific method comprises the following steps:
1, wipe it with some alcohol on a paper towel, wipe it a few times and then tear it clean.
2, using acetone, the method is similar to alcohol, but acetone can remove these residual gums very quickly and easily, which is better and more thorough than alcohol.
3, use nail polish remover, the usage is the same as alcohol acetone, and the effect is also very good.
4. Use hand cream, first tear off the printed matter on the surface, then squeeze some hand cream on it, rub it slowly with your thumb, and it will fall off after a while.
5. banana oil and banana oil are industrial chemicals used for paint stripping, which are easy to buy. Just use a paper towel to wipe the label adhesive with banana oil.
6. Mix the detergent with water and apply it to the label, soak the label completely, then cover the label with plastic wrap, wait for about five minutes to uncover the plastic wrap, and then gently pull the label down.
7. Apply essential balm to the residual rubber and wipe it back and forth with a paper towel. This method will make the residual rubber thinner, but there is a greasy layer on the object because of the oiliness of the wind oil essence. If you hate it, you can wash it again with greasy detergent.
8. soak in hot water for a while, or blow with a hair dryer, bake the glue and it will fall off, and then you can peel it off.
9. You can use an eraser. At first, you may feel that the more you rub it, the dirtier it is, but you will see the effect after rubbing it for a long time, but this method is more tiring.