General inspection knowledge of garment acceptance documents (summary)

Knitted fabric

1. Knitted seams should not be too loose or floating, and the seams should be flexible.

2. The elasticity of knitting should be enough, and there should be a transparent belt at the shoulder seam.

3. Knitted waist, neck and cuff should have enough elasticity or resilience.

4. Knitted fabric should not leak yarn, the weight should be consistent, the ironing should be good, and it should not be pulled apart.

fabrics

1. The fabrics of ready-made clothes are of the same quality and should not be too fragile.

2. The same batch of clothes can't have color difference (except for special processes and situations).

3. The fabric can't have yarn drawing, weft skew and dead crease marks.

4. The fabric shows no irregularity, flaw or stain.

ironing

1. Clothing ironing should be smooth and the sleeves should be smooth.

2. The whole dress should have a three-dimensional effect.

3. There should be no scalding marks at the seams, setting pleats and swinging seams.

4. the lining should be ironed and leveled.

5. There must be no auroras or scalds during ironing.

suture

1. The color of suture is correct.

2. The thread fastness should be sufficient (especially in the buttocks, underarms and shoulders).

3. The elastic tension of the thread should be enough, and the suture should be trimmed well.

4. The suture line should be suitable for clothes, and all threads should meet the thread standard.

sewing situation

1. The sewing needle distance should be right, and the fabric should not be damaged when sewing.

2. There should be no continuous needle holes and wire drawing at the sewing place.

3. The sewing edge should be trimmed and cleaned, and the sewing should be straight without wrinkling.

4. The ready-made clothes should not be twisted, and the appearance of stitching should be beautiful.

5. the seam joint is symmetrical (except under special circumstances)

hemming and color fastness

1. The hemming width is uniform, the stitch distance is uniform, and there is no stitch skipping and leakage, and the joint phenomenon is obvious.

2. The rubbing color fastness of fabrics and linings, ornaments, prints and buttons should not cause stains on garments.

3. belts and ropes should not cause stains.

trademark, size label, washing component label, special label and tag

1. The size of the trademark is correct, the fixing method is correct and the binding position is correct.

2. The size mark is consistent with the ready-made clothes, and the position is correct. The size mark should be fixed firmly.

3. The position of the washing component label is correct, the washing method is correct, and the component label is correct.

4. The special mark is correct and should be fixed firmly.

5. The ready-made clothes must have a price tag, the hanging position of the price tag is correct, and the price should be correct.

6. The composition and model number on the tag are correct, and the adhesive paper on the tag is pasted in the right direction.

7. The color on the tag matches the ready-made clothes, and the tag is not damaged and displayed clearly.

Third, the quality inspection of down jackets and cotton-padded clothes

The front placket

The cotton of the Bank of China is symmetrical left and right.

flap

1. It should be flat, wrinkle-free, twist-free, and the seam is not upturned.

2. The face is tight, and the folding amount of the front face of the cover is not there when sewing.

3. The width and width of the wiring are consistent (no wiring).

4. If the zipper has no cover, it has no wiring.

vermicelli

1. The tightness is appropriate according to the specifications.

2. The whole cotton seam allowance should not be too hot.

3. The sewing is straight and even.

hat

1. The width of the hat door is consistent

2. The drawstring and elastic band are suitable (according to the process)

The whole

cotton and down can't be exposed, and the rest parts can refer to the quality inspection of the above-mentioned garments

4. Denim washed cotton fabrics

1. Roving, yarn walking and damage.

2. whether the washing process is up to standard with uniform color, straight grain, straight folding, no obvious stains and no holes (except special process).

V. Sweaters (refer to the quality inspection of garments for others)

Appearance inspection

Coarse and young hairs, flying hairs, pilling, snakebite, uneven color of mixed hairs, missing needles, loose and weak sweater body, insufficient washing softness, white marks (uneven dyeing of pieces) and stains.

size inspection

strictly follow the size table.

Symmetry test

1. The size of the collar tip and whether the collar bone is relative;

2. Width of two shoulders and two clips;

3. The sleeves are long and the cuffs are narrow.

Manual inspection

1. Common defects of lapel models: loose neckline, too wide hollow lapel, twisted and skewed front and exposed bottom tube;

2. Common defects in the collection: the neckline is too loose and the horn is too tight;

3. Common defects of other models: jacked angle, too tight at the foot of the shirt, too straight at the pit of the needle drawing, wavy at the foot of the shirt, and uneven lateral bones on both sides.

measurement error (+/-) range of bulk goods (unit CM)

Note 1: In case of elastic fabric and diagonal silk fabric, it can be appropriately increased (decreased) by .5cm—1cm.3;

note 2: the dimension error is based on the process sheet (please refer to this sheet for the discrepancy between the physical object and the process sheet) and the auxiliary material card (the auxiliary material card comes with the washing label and tag template);

flour accessories

1. check whether there are any defects such as yarn skipping, stains, oil stains, color difference, etc.

2. Pay attention to the reverse direction of the material (the pieces should be cut in one direction (the pattern is consistent in reverse direction (the strip or grid material is symmetrical left and right).

3. Pay attention to the front and back of the material! Generally, the front side is flat and smooth (soft to the touch (fine and fine (clear lines (shiny) (the lines on the back side are not obvious (the luster is gloomy).

regulations on the deviation of silk grain

1. Front garment piece. The following seam allowance shall prevail (1 cm outward inclination is allowed: < P > 2. Rear garment piece. The rear center line shall prevail (1 cm outward inclination is allowed: < P > 3. Large sleeves. The front sleeve seam shall prevail (the cuff is allowed to be tilted 1cm forward and 1 cm backward: < P > 4. Sleeve pieces. The front sleeve seam shall prevail (the cuff is allowed to tilt 1cm forward (1cm backward:

5. Collar. It is allowed to be inclined by .5cm (it is allowed to be inclined by 3cm in the collar: < P > 6. Front and rear pants. The stitching line shall prevail (the lateral seam at the foot mouth is allowed to deviate by 1cm (the downward crotch seam is allowed to deviate by .5cm (but it is not allowed to incline backwards:

7. The waistband is allowed to deviate by .3cm).

regulations on skewness of summer clothes

1. No skewness is allowed for the front garment, leader, over-the-shoulder, sleeve head and pocket:

2. The back garment is based on the center line of the back seam (.4cm left and right skewness is allowed:

3. The sleeve is based on the center of the sleeve (.4cm left and right skewness is allowed.

(inspection and verification form)

VI. Sample garment inspection of different fabrics

I. Style category: jacket category

Fabric category: tweed, cashmere, woolen and knitted fabrics, and the requirements and error standards for cutting such fabrics are as follows:

1. The length of the front and rear pieces (length of garment, length of front placket and length of side seam) is allowed.

2. The width error of the front and rear films (chest circumference and swing circumference) is allowed to be .3cm..

3. The allowable error of the front and rear collars is .2cm..

4. The length error of small sleeve film (inside length, outside length) is allowed to be ±.3cm.

5. The error of large and small sleeves (sleeve fat and cuff width) is allowed to be ±.2cm.

6. The lining, front, back, large and small sleeves should be the same as the surface cloth. However, the inclination of the hem thread should not exceed 1.5 cm.

2. For composite materials, coatings, leather and suede, the error standards of such cutting pieces are as follows

1. The length error of the front and rear pieces (the total length of the garment, the length of the placket and the length of the side seam) is allowed to be ±.2cm.

2. The width and width error of the front and rear films (chest circumference and swing circumference) is allowed to be .2cm..

3. The error of front and rear collar is allowed to be .2cm..

4. The length error of large and small sleeves (inner length and outer length) is allowed to be ±.2cm.

5. The allowable error of large and small sleeves (sleeve fat and cuff width) is ±.15cm.

6. The length and width errors of lining, front and back panels and large and small sleeves are not allowed to be ±.3cm. However, the inclination of the hem thread shall not exceed ±.15cm. Medium-length, windbreaker and cotton jacket: the fabric is the same as the jacket fabric

III. Woolen, cashmere, worsted and knitted fabric

1. The front and rear pieces (length of garment, length of the placket and length of the side seam) are three lengths, and the allowable error of length is .4cm..

2. The width and width error of the front and rear films (chest circumference and swing circumference) is allowed to be .2cm..

3. The error of front and rear collars is allowed to be .15cm (size).

4. The length error of large and small sleeves (inner length and outer length) is allowed to be ±.2cm.

5. Allowable width error of large and small sleeves (sleeve fat, cuff width) is ±.15cm.

6. The lining, front and back panels and large and small sleeve panels shall meet the same requirements. However, the inclination of the hem thread shall not exceed ±.15cm.

iv. composite material, coating, leather and suede

1. The length error of the front and rear panels (length of garment, length of front seam and length of side seam) shall not exceed .1cm..

2. The width of the front and rear films (chest circumference and swing circumference) shall not exceed .2cm..

3. The size error of the front and rear collars is allowed to be .15cm..

4. The length error of large and small sleeves (inner length and outer length) is allowed to be ±.15cm.

5. There is no error in the size of large and small sleeves (sleeve fat, cuff size).

6. The length and width errors of lining, front and back panels and large and small sleeve panels shall not exceed ±.3 cm, and the thread inclination shall not exceed ±.15cm

7. For the cut pieces which are changed after lining pressing, the errors of the main panel and the auxiliary panel of various fabrics shall not exceed ±.1 cm.

8. After the fabric with stripes and squares is cut into pieces, the errors of left and right pieces, front and back, shall not exceed .1cm, especially for striped fabrics, and the front and middle parts shall be in a straight line.

9. if there are all the main and auxiliary pieces of corduroy, worsted, pure cotton, hemp, spun silk, silk and this kind of fabric, no error is allowed regardless of length and width, except lining.

The above contents refer to the error standard of the molded pieces. I hope that it will not exceed this standard in actual operation, and be meticulous and quality first. If the above errors are found during sewing and film inspection in the workshop, the workshop will arrange to repair the film and handle it by itself.

VII. Packaging inspection

1. Thread ends and stains should be cleaned up.

2. Clothes should be ironed evenly, and there should be no scalding marks. After ironing, the water vapor should be exhausted before being put into the bag.

3. If the clothes are wiped with a cloth with water, the clothes should be dried before being put into the bag.

4. Copy paper should be added to clothes made of cotton fabric, and copy paper should be added to printed clothes.

5. Hang the tag at the specified location and paste the self-adhesive sticker at the specified location.

6. Plastic bags must not be damaged.

7. Correct proportion, no mixed loading and short loading;

8. A pad should be added at the sealing of the carton to prevent the clothes from being cut when unpacking (if there are inner boxes, the pad should be placed in the inner box instead of the outer box, and the pad should be distributed according to the number of inner boxes when distributing).

9. The carton size is moderate. After unpacking, the clothes should be flat. If the carton is damaged and sunk during inspection or the paper is too soft and damp, it should be replaced immediately. ;