Simple classification is as follows:

1. Assembly categories: pneumatic screwdriver, air wrench, air cannon, ratchet wrench, piercing wrench, fixed-torque air screwdriver and fixed-torque wrench;

2. grinding: pneumatic disc sander, square sander, miniature sander, irregular sander, eight-petal sander, pneumatic belt sander, pneumatic sander and pneumatic polisher;

3. Grinding category: pneumatic angle grinder, engraving grinder, engraving and grinding pen, pneumatic file, ultrasonic file machine;

4. Drilling category: straight air drill, portable gun air drill, right-angle elbow air drill, professional aviation air drill and off-angle air drill;

5. Tapping threads: portable pneumatic tapping machine, desktop mechanical arm set tapping machine and portable pneumatic threading machine;

6. Stone tools: pneumatic water mill, pneumatic stone cutting machine;

7. Riveting category: pneumatic cap pulling gun and pneumatic nail pulling gun;

8. shearing category: pneumatic scissors, pneumatic wire pressing pliers and pneumatic saws;

9. Painting category: spray gun, oil pump, paint pipe, air pipe, pneumatic pressure barrel and pneumatic agitator;

1. Nailing guns: straight nail guns, yard nail guns, steel nail guns, roll nail guns

, pneumatic box sealers, C-type guns, yard clamping guns, figure nail guns, etc.

11. tamping category: air shovel, air pick, needle rust remover and pneumatic rock drill.

pneumatic tools and electric tools

What are the differences between pneumatic tools and electric tools? Among hardware tools, electric tools and pneumatic tools are two very common and used tools, but today, Guangdong Xiquan Electromechanical Co., Ltd. has compiled and analyzed the following for you: the output power is large according to the ratio of weight to volume, and it is smaller and lighter than electric tools under the same output power. There is no overload fault, even if the pneumatic tool is overloaded. The tool just stops rotating, and once the overload phenomenon is relieved, it will automatically resume normal operation, which has no influence on the tool and will not cause any failure; However, if the electric tools are overloaded, they will generate heat and even burn the motor, which will lead to high maintenance cost and affect the work progress and efficiency. Seriously, it will also threaten the life safety of operators. It is simple to use and maintain, and it can be used when it is connected to the air source. When it is used daily, two drops of sewing machine oil are added to the air inlet of the tool, and the air compressor drains more water. Strong water resistance, although immersion is harmful to tools, it will not be as deadly as power tools; The unique explosion-proof structure can be used in places with explosion danger, such as coal mine operation, because it will not produce electric sparks. Speed adjustment and output power adjustment are simple, which can be carried out simply by operating the handle of the air supply valve and adjusting the regulating valve, and the air supply source can also be adjusted and controlled. Save energy and reduce costs. Equipped with a standard air source in the industrial workshop, you can bring multiple tools to work at the same time. Long service life and high safety. Because it is a device that uses the energy of compressed air provided by the air compressor as the power source, it will not cause the phenomenon of electric tools leaking electricity and hitting people, nor will it produce electric sparks. It can be owned in any place and will not pose a threat to the environment. Pneumatic, one of the most effective means of automation and mechanization, is widely used in all walks of life with high efficiency and high speed. 1. Working ability: Both of them provide many different working modes, but the speed adjustment and output power adjustment of pneumatic tools are simple, and they are smaller and lighter under the same output power. In addition, the pneumatic tool can provide more choices in the speed range, and there is no fever or overload fault. When the overload occurs, the starting tool only stops rotating, and once the overload phenomenon is relieved, it will resume normal operation.

picture of pneumatic tools

an air shovel is a pneumatic tool. Similar to the wind pick, a shovel or chisel is used instead of a drill to separate the soil on the rock mass or level off the burrs of castings. Zmjt2 air shovel is mainly used for sand cleaning of castings, deburring of large, medium and small castings, shoveling and cutting weld grooves, and correcting the openings of stone and concrete walls and brick walls.

what kind of pneumatic tools belong to

pneumatic tools. They belong to group 743, category 7 of the trademark classification;

according to statistics, there are 232 registered trademarks of pneumatic tools.

how to choose other minor categories when registering:

1. There are 2 trademarks with registration category, accounting for .86%

2. There are 2 trademarks with registration category, accounting for .86%

3. There are 2 trademarks with registration category, accounting for .86%

4. Select registration category. The registration ratio is .86%

6. There are 2 trademarks with registration category, and the registration ratio is .86%

7. There are 2 trademarks with registration category, and the registration ratio is .86%

8. There are 2 trademarks with registration category, and the registration ratio is .86%

. The registration ratio is .86%

1. There are 2 trademarks with registered category, and the registration ratio is .86%

What category does pneumatic products belong to < P > Pneumatic equipment belongs to the 749 group of the seventh category of trademark classification;

according to the statistics of signpost network, there are 83 registered trademarks of pneumatic equipment.

how to choose other minor categories when registering:

1. One trademark with registration category is selected, and the registration rate is 1.2%

2. One trademark with registration category is selected, and the registration rate is 1.2%

3. One trademark with registration category is selected, and the registration rate is 1.2%

4. The trademarks with registration category are selected. The registration ratio is 1.2%

6. One trademark with registration category is selected, and the registration ratio is 1.2%

7. One trademark with registration category is selected, and the registration ratio is 1.2%

8. One trademark with registration category is selected, and the registration ratio is 1.2%

9. Select registration, and cool the lubricant supply and processing equipment. Debris processing equipment, mainly including pulverizer, centrifugal separator and briquetting machine, has one trademark with group number: 75, accounting for 1.2%

1. One trademark with registered category has been selected, accounting for 1.2%.