Install the blade cover on the suction motor, and fasten the four holes of the blade cover to the blade with buckles. As shown in the figure, fasten its four feet to the slots of the blade cover, cover the motor cover to the blade cover, and fasten the four slots to the four feet of the blade cover.
Place the socket in the position shown in the figure of the cover with a glue-dispensing fixture, and place the sponge on the cover of the socket, and compact it around, so that the other side of the sponge is placed on the other side of the cover.
Put the guide cover under the lamp, install the key spring for releasing the dust cup on the dust cup release button, then release the button to cover the keyhole, install the switch reset spring on the opened key, and then open the key to cover the button hole.
Cover the indicator on the lampshade, gently press it with your hand, and fasten the two ST3 * 8 screws to the end with an electric screwdriver. Button button to test whether it is smooth and not blocked.
Put the charging socket into the slot under the socket shell. Use an electric screwdriver to cover the two ST3 * 8 fastening screws of the socket cover. Assemble the battery cover to the battery card slot, and clip the black cable to the gap between the battery card slots.
Install the motor cover assembly to the next one, and make sure that the motor is installed in place. Straighten out the joints and tie them together with cable ties.
Align the main PCB button with the button hole of the indicator lamp cover, and install it on the indicator lamp cover, and the indicator lamp cover clips the PCB button.
The indicator card should indicate the lamp slot of the lampshade, and the lamp should be flush with the end face of the lamp slot. Press a button, this button is not a light switch on the PCB, it is resolutely resisted. From cover to cover, button Kaka to slot.
Put the lid on. Put the machine bottom up on the tooling, and use an electric screwdriver to fasten five ST3 * 12 screws under the machine screw holes. The dust cup on the machine. The blade under the flat side is placed on the ultrasonic tool mold. The blade cover is convex, there are three holes in the blade, and there are three fixed columns on the blade. Start the ultrasonic tool with both hands and fix the blade cover on the blade. Fixed blades of wind power assembly.
Dust cup mounted on ultrasonic machining mold. The direction of the trademark cover is shown in the trademark groove on the dust cup cover. Manually start the ultrasonic tool, and the trademark cover is fixed on the dust cup. Dust cup assembly.
Put the dust cup under the ultrasonic tooling mold as shown in the figure and fix it. Dust from the mouth of the dust cup to the notch. Cover the dust cup with a film, manually start the ultrasonic tool, and fix the mouth of the dust cup on the dust cup. Ultrasonic dust cup opening of dust cup assembly.
Move the dust cup to the fixture on the fixed mold in the direction shown in the figure. Take the big end of the front axle, once the wheel passes through the plane of the E end, turn the wheel to ensure that the wheel rotates smoothly, and then put the front axle flat on the shaft hole of the dust cup and put it on the dust cup.
Press the tooling button by hand to press the wheel and axle on the dust cup. Good dust cup assembly of pressure wheel. Dust plug installed on the dust cup of the air inlet.
Take it after the filter and filter element self-inspection. After installing the filter element into the 3.6 V mesh base, hold the filter element and rotate it in the direction shown in the figure, and then clamp the filter element into the clamping slot. The assembly is installed behind the screen outside. The filter element is put into the dust cup.
Clean dirt, grease and dust cups with a clean flannelette machine. Nameplate label used to mark the slot at the bottom of the machine.
Take one end of colored adhesive tape and fold it in half for 20 mm, and then switch it behind the switch button of the machine with colored foam tape. As shown in the figure, the distance between the protective foam edge and the switch is more than 5 mm visually, and wrap it with adhesive tape.