We often use the plastic basin, and the bottom of the plastic basin usually has a trademark label. After tearing it off, there is often an embarrassing situation that the glue is still on it, which is sticky to the touch and very inconvenient to use. How to remove the label glue from the plastic basin? There are several ways to remove the label glue from the plastic basin:
Method 1
1. Prepare a paper towel, white vinegar and a small water cup. First, put the paper towel on the label place on the plastic basin, pour a few drops of white vinegar into the cup, and then pour the white vinegar on the paper towel on the label.
2. Wait for about 1 minutes, take away the paper towel, and gently tear the label with your fingernail, so you can easily remove the label glue from the plastic basin.
Method 2
1. Pour some wind oil essence on the plastic basin, and then wipe it in the same direction with a wet cotton cloth.
2. After the glue is pushed in one direction, don't take it off in a hurry, let it be glued together and then take it off directly, so that the cotton cloth will not be stained with glue.
Method 3
1. First, iron the plastic basin with hot water, and then scrape the glue off the plastic basin slowly with a blunt metal tool.
2. Be careful not to scratch the plastic basin, because the plastic basin is afraid of metal. If it is scratched, it will easily lead to uneven surface of the plastic basin. Scrape it slowly.
Method 4
1. Turn on the hot air gear of the hair dryer. Blow the label glue constantly with a hair dryer.
2. When the glue on it is blown hot, the label glue will soften slowly, and it can be easily taken off after blowing soft.
Method 5
Repeatedly stick and tear with adhesive tape, so that the label on the plastic basin can be glued down.
Method 6
Use soapy water and appropriate amount of ammonia water to clean up, which can clean up a lot of impurities on it.
Method 7
Use special cleaning agent or decontamination paste on sports shoes to scrub and remove.
Generally speaking, there are many ways to remove the label glue from the plastic washbasin. If necessary, you can refer to the above methods and use them directly. However, if you use metal utensils, you should avoid scratching the plastic washbasin.
second, how to remove the label glue from the stainless steel washbasin
The label glue also needs to be removed from the stainless steel washbasin, but there are some differences between the method of removing the glue from the stainless steel washbasin and the plastic washbasin. The specific methods include:
1. Wipe it with some alcohol with a paper towel, and then wipe it clean after a few rubs.
2. The method of using acetone is similar to that of alcohol, but acetone can remove these residual gums very quickly and easily, which is better and more thorough than alcohol.
3. Use nail polish remover in the same way as alcohol acetone, and the effect is also very good.
4. With hand cream, first tear off the printed products on the surface, then squeeze some hand cream on it and rub it slowly with your thumb. After rubbing for a while, you can rub off all the sticky residual glue.
5. banana oil and banana oil are an industrial agent used to remove paint, which is easy to buy. Just stick some banana oil on the paper towel to wipe the label glue.
6. Mix the detergent with water and apply it to the label, completely soak the label, then cover the label with plastic wrap, wait for about five minutes to uncover the plastic wrap, and then gently pull the label down.
7. Apply the essential balm to the residual glue and wipe it back and forth with a paper towel. This method will make the residual glue thinner, but because of the oiliness of the essential balm, there is a greasy layer on the object. If you hate it, you can wash it again with a detergent that removes the greasy.
8. soak in hot water for a while, or blow with a hair dryer, and then bake the glue to get it off, and then peel it off.
9. You can rub it with a rubber. At first, it may get dirtier, but if you rub it for a long time, you will see the effect, but this method is tiring.