Main requirements for passing the bullet train inspection
serial number
project
Qualification requirements
Vehicle identification code (the whole vehicle leaves the factory)
Number)
Cars, motorcycles, semi-trailers and mid-axle trailers that leave the factory on September, 20 12 should have unique vehicle identification codes, and at least one vehicle identification code should be engraved on the frame part (vehicles without frames are the main load-bearing parts of the body and cannot be disassembled) to prevent corrosion and wear. Passenger cars and trucks (except low-speed cars) that left the factory on March 20 13 1 day shall also provide permanently maintained vehicle identification codes that can be clearly read from the outside; Other motor vehicles shall be engraved with the vehicle model and factory number, with the model in front and the factory number behind, and the starting and ending marks shall be engraved at both ends of the factory number. Low-speed vehicles leaving the factory on April 1 2007 shall be marked with vehicle identification codes as required.
It is not allowed to engrave the vehicle identification code and vehicle model and factory number on the same vehicle at the same time. All vehicle identification codes (or vehicle factory numbers, the same below) marked on the same vehicle shall have the same content. A modified car manufactured before June 65438+1 October12004 may have two different vehicle identification codes. At this time, a vehicle identification code should have the same content as the relevant documents.
The engraved vehicle identification code should be easy to read and print, and its content should be consistent with the vehicle identification code recorded in relevant documents (vehicle factory certificate, goods import certificate or motor vehicle driving license) and marked on the vehicle product number plate, and there should be no obvious alteration, change, chisel, repair, polishing mark or gasket, and it is not allowed to be engraved without authorization. Cars, motorcycles, semi-trailers and mid-axle trailers that were delivered from the factory on September, 20 14/0/day should not have any cover on the surface with a large enough area around the carving area when viewed from the top (front); If there is a cover, the words "vehicle identification code" or "VIN" should be clearly marked on the surface of the cover, and the cover should be directly removed (or uncovered) and restored without using any special tools.
Engine (motor) model and factory number
The engine model and factory number should be engraved (or cast) on the cylinder block and can be permanently preserved; The engraved engine factory number should not have obvious abnormal conditions such as chiseling, repairing, polishing marks or unauthorized engraving. If the engraved (or cast) engine model and factory number are not easy to see, permanent identification of the engine model and factory number should be added to the easily seen part of the engine.
Pure electric vehicles, plug-in hybrid vehicles, fuel cell vehicles and electric motorcycles, which were delivered from the factory on March 20 13, shall be engraved with the motor model and number on the shell of the main drive motor; If the cover engraved with the motor model and number is covered, an observation port should be left, or permanent motor model and number identification should be added to the cover.
The "engine model and factory number" recorded in the relevant documents shall be consistent with the engine model and factory number engraved or cast on the engine block (or marked on the logo) and marked on the nameplate of the vehicle product.
Note: For motor vehicles manufactured before June 65438+1 October1day, 2004, if the engraving model and factory number of the engine are not easy to see, the visible part of the engine may not have the engine logo.
Vehicle brand
/model
At the time of registration inspection, the "vehicle brand" and "vehicle model" recorded on the vehicle factory certificate (domestic motor vehicle), customs import certificate (imported motor vehicle) and other documents shall be consistent with the vehicle brand and model indicated on the vehicle product label.
body colour
When registering for inspection, the body color shall be verified according to the actual vehicle; When changing the body color, fill in the body color according to the actual car.
In other cases, the body color should be consistent with the body color recorded in the motor vehicle driving license.
serial number
project
Qualification requirements
Approved number of passengers
During the registration inspection, the number of passengers/cab occupants shall be verified according to GB 7258-2012, 4.5.2 ~ 4.5.6 and 1 1.6. For domestic motor vehicles, trucks and special operation vehicles subject to announcement management, the number of passengers approved in the cab and passenger cars shall be consistent with the value indicated on the motor vehicle factory certificate and conform to the relevant provisions of announcement management. In other cases, the number of seats/bunks should be consistent with the contents recorded in the motor vehicle driving license.
License plate (frame)/vehicle license plate
Check the motor vehicle number plate (frame) during the registration inspection: the front number plate (frame) (except motorcycles) should be located in the middle or right of the front (according to the driving direction of motor vehicles), the rear number plate (frame) should be located in the middle or left of the rear, and the number plate (frame) should be equipped with a motor vehicle number plate meeting the requirements of GA36. On March 20 1, 20 16, two license plate mounting holes should be set on each license plate (frame) of motor vehicles, and on March 2065438, four license plates (frames) should be set on each license plate (frame) [three-wheeled vehicle front license plate (frame) and motorcycle rear license plate (frame)]. The number plate mounting hole shall ensure that the number plate can be directly, firmly and reliably mounted on the vehicle with M6 bolts.
In other cases, check the vehicle number plate: the number plate should be installed at the number plate (frame), which should be vertical, horizontal and basically vertical, and sealed with a special sealing device conforming to GA804. The license plate shall not be deformed, covered, damaged or altered. The number and type of the license plate shall be consistent with the records on the motor vehicle driving license, and its Chinese characters, letters and numbers shall be clearly distinguishable without obvious color difference. Detachable license plate holders and reversible license plate holders are not allowed.
vehicle
Appearance shape
The light transmission surface of external lighting lamps should be complete, and the colors of light transmission surfaces of symmetrically arranged external lighting lamps with the same function should not be obviously different. The rearview mirror and rearview mirror equipped with motor vehicles should be in good condition. All window glass shall be intact, and mirror reflective sunshade film shall not be attached. The visible light transmittance of the windshield and the glass other than the windshield used in the driver's visual area shall be greater than or equal to 70%, and the visible light transmittance of all the windows of road buses, tourist buses and school buses (including special school buses and non-special school buses) shall be greater than 50%. Opaque colored paper or any heat insulation paper with specular reflection materials shall not be posted.
Vehicles equipped with trademarks, factory marks and other vehicle signs should be compatible with the brand/model of the vehicle.
At the time of registration and inspection, the appearance and shape of domestic motor vehicles subject to the announcement shall be consistent with the photos of motor vehicles in the announcement, except for those equipped with optional parts allowed by the announcement; Windows should be set on both sides of the cab (area) for vans and closed trucks that were delivered from the factory on September, 20 12 1 2, and no windows should be set on the cargo compartment [except the observation window for observing the cargo state in the cab (area)]. In other cases, the appearance and shape of the vehicle shall be consistent with the appearance and shape of the vehicle recorded in the standard photo of the motor vehicle on the motor vehicle driving license, except for the parts that are allowed to be installed by themselves; If the motor vehicle license plate is hung on the standard photo of the motor vehicle, the number and type of the license plate shall be consistent with the contents recorded in the motor vehicle driving license.
Note 1: Inspectors can check the standard photos of motor vehicles by collecting the information.
Note 2: The visible light transmittance of the side window glass of road buses and tourist buses that were manufactured before September 20 1 21is less than 50%, which is not considered as substandard.
tyre
in perfect nick
The tread depth of tire crown shall meet the requirements of 9. 1.6 in GB 7258-2012. Tread and sidewall should be free of cracks, defects, abnormal wear and cuts that affect the use, and tread should not be exposed to tire plies due to local wear. Tire nuts should be complete. All wheels of road buses, tourist buses and school buses and steering wheels of other motor vehicles shall not be equipped with retreaded tires.
At the time of registration and inspection, the number of tires shall be consistent with the data recorded in the relevant documents such as the motor vehicle factory certificate; In other cases, the number of tires shall be consistent with the number of tires recorded in the standard photos of motor vehicles on the motor vehicle driving license.
automobile
Triangle warning sign
Cars (except for three-wheeled cars without cab) shall be equipped with triangular warning signs for motor vehicles, which shall be properly placed in the car, and the style and size shall comply with relevant regulations.
lap-belt
Equipped with car seat belts should be complete and can be used normally. Each sleeper of a sleeper bus should be equipped with a two-point car seat belt.
At the time of registration inspection, passenger cars, road buses, tourist buses, buses without passenger standing areas, all seats of tourist buses, driver's seats and front seats of other cars (except low-speed cars) delivered from September 1 and 20 12.
The above contents are compiled and published by Pacific Auto Network for reference. I hope it helps you. If you need more legal answers, you can consult Pacific Auto Network online.
Million car purchase subsidy