Speaking of casement glass doors, I believe everyone must be familiar with them. In today’s decoration, casement glass doors can be seen everywhere, such as hotels, shopping malls, offices, etc. In addition to partitions, casement glass doors It also plays a beautiful and easy-to-observe role. For example, the flat-opening glass doors in hotels and shopping malls can see the decoration and ornaments inside at a glance. In offices, the flat-opening glass doors play a transparent and observable role. effect. Although casement glass doors can be seen everywhere, I believe many people still don’t know the relevant knowledge about casement glass doors. Let me explain to you the dimensions and installation methods of casement glass doors!

The casement glass door is divided into framed or frameless, and its size will be flexibly determined according to the actual situation:

1. With frame If the accessories meet the requirements, it can be made to be more than 1500x3000mm, such as the floor spring door used in shopping malls. Of course, the strength of the four frames must be sufficient

2. When there is no frame and it is just a door clip, it should not be larger than 1100x2200mm.

3. Ordinary doors, whether framed or not, are mostly 1000x2100mm.

How to install the casement glass door?

The installation of the casement glass door is more complicated than the installation of doors made of other materials. The installation project of the casement glass door must be very careful and attentive, so that you can Effectively avoid unnecessary harm. The flat glass door is a special type of door. Its thickness determines that it is not a solid door, and it does not match the characteristics of heterosexual doors. The reason why it is called a glass door is mainly because its material contains glass. For example, when tempered transparent glass is used, the door leaf has a transparent function, while when frosted glass is used, it has a semi-transparent function. Now let’s take a look at the installation steps for swing glass doors. The installation methods of flat glass doors vary depending on the type.

1. Preparation before installation: Before installing thick glass doors, ensure that the ground construction has been completed and the stainless steel or other decorative door frames have been completed. The thick glass limit slot has been set aside. Be very careful when chamfering the four corners - usually use a fine grinding wheel in hand to grind the corners slowly to prevent edges and corners from chipping. The wooden base with stainless steel finish should be fixed to the ground using wooden wedge nails. Glue can then be used to stick the stainless steel veneer panel to the wood. Aluminum alloy square tubes can be fixed to frame columns with aluminum angles, or fixed to wooden wedges embedded in the ground with wood screws.

2. Installation and construction: First use a glass suction cup to suck the thick glass tightly, and then hold the suction cup to lift the thick glass plate. It requires 2-3 people to lift it at the same time. After lifting the thick glass plate, first insert it into the limit groove on the top of the door frame, then place it on the bottom bracket, and adjust the installation position so that the edge of the thick glass plate just seals the stainless steel facing seam of the side frame column. mouth.

3. Inject glass glue to seal: first open the glass glue and put it into the glass glue injection gun, and then use the rear pressure rod end plate of the glass glue gun to hold the bottom of the glass glue tank . Hold the glass glue injection gun body with your hand and hold the glue injection handle with one hand, and operate the pressure handle in a cycle of loosening and pressing to squeeze out a small amount of glass glue and inject it. Then align the glass glue injection port with the gap end and seal it.

4. Butt jointing of thick glass plates: The fixed part of thick glass plates often cannot be completed in one piece. When docking thick glass, pay attention to the docking gap between 2-3mm, and the edges of thick glass need to be chamfered. After the two connected pieces of thick glass are positioned and fixed, inject glass glue into the gap. After filling, use a plastic sheet to scrape the glass glue on both sides of the thick glass, and wipe off the glue traces with a clean cloth.

After seeing this, I believe everyone has some understanding of the size and installation plan of casement glass doors. In fact, casement glass doors are very practical in daily decoration, both for individuals and enterprises. Due to their various advantages, casement glass doors have gradually replaced traditional glass doors. Casement glass doors make home decoration more convenient and beautiful. The methods mentioned in this article are only a small part of them. If you have any ideas, install casement glass doors. Friends with glass doors can refer to it, but they should also combine it with on-the-spot inspections and make detailed analysis!

Tubatu Online provides you with "each decoration quotation, 1-4 local decoration companies, and 3 sets of decoration for free" Design Plan", as well as decoration avoidance strategies! Click this link:/yezhu/zxbj-cszy.php?to8to_from=seo_zhidao_m_jiare&wb, and you can get it for free~