1. Press and hold the unlock and lock keys of the remote control to turn on and off the voice function.

2. Replace an alarm or remove the connecting wire of the alarm.

The voice horn of intelligent voice anti-theft system for electric vehicles, and the introduction of its function;

Set the key. Please pay attention to safety under normal conditions. The voice broadcast of the beeping horn has been strengthened, and it will be banned in 2 seconds. In the forbidden state, it will be broadcasted by voice for the first time (don't touch me) for three times, and then it will be shocked again within 10 seconds and directly enter the multi-voice alarm locking motor.

After the switch is forcibly turned on, both sides of the speaker broadcast (catch thieves) and then directly enter the multi-voice alarm motor locking state. Press the set key to suspend the alarm during the alarm process, but it is still in the alarm state.

Extended data:

Common sense of electric vehicles:

1. The screws and nuts fastened to the bicycle shall be tightened, and shall not loosen or fall off.

2, rotating parts should be flexible operation, can not have stuck, stiff phenomenon. For example, the front and rear wheels should rotate flexibly, and they should not swing from side to side or jump up and down. When the wheel is about to stop, it should be able to swing back and forth briskly, and it should not stop suddenly. The handlebar should rotate freely from left to right, and the pedal shaft and crank should be fastened, and they should not loosen each other and rotate flexibly.

3. The shift position of the gearbox is correct within the shift range, and the shift position should be clear with no gap in the middle.

4. The chain should be elastic and flexible. Shake the crank sprocket back and forth repeatedly by hand, the chain can run flexibly, and there can be no chain jumping or falling.

5. Hold the front and rear parts of the saddle with both hands, and press down the front end of the saddle with one hand. The front end of the saddle should not collapse. Then turn the saddle horizontally with both hands. Do not turn the saddle.

6. Selection of braking and braking system: Hold the handlebar with both hands, brake left and right respectively, and push and pull the bicycle back and forth at the same time. At this time, the wheels should not turn; Loosen the handle and the braking system should be able to reset quickly.

7. The surfaces of all parts shall be clean, free from stains and rust, and the trademark decals shall be complete and clear, free from sharp edges and burrs. There shall be no tingling at the edges such as mud pieces and chain sleeves, and the ends of steel wire ropes such as brakes shall be provided with protective sleeves.

8. Observe the brand or label of the parts. Generally speaking, good parts are marked with obvious trademark marks and the patterns are clear and exquisite, while inferior products are rarely marked or rough.

9. Each part of the switch is sensitive and reliable.

10, the speed regulation is stable and reliable. Turn the speed control handle slowly, and the motor should start and accelerate smoothly. After releasing the handle, the handle can be quickly reset and the motor will decelerate evenly.

1 1, brake power failure is fast and reliable. Turn the speed control handle. After the motor is running, tighten the brake and the motor can be powered off immediately. If there is a power display, you can see that the display is zero.

12, the battery is easy to disassemble and assemble. The weight of lead-acid battery is generally around 13.5kg, because it needs to be disassembled every day, so the position of the battery must be suitable for your body.

Common sense of riding an electric car:

Vehicle maintenance includes checking whether all the screws and nuts of the vehicle are firm, whether the control performance is good, whether the tires need to be replaced, whether the mechanical system is in good condition, whether the battery capacity is up to standard, and the brushed motor is maintained once a year. Fill it out carefully after maintenance. The specific maintenance contents are as follows:

(1) debug the whole vehicle, check whether there are any hidden dangers in the electrical control circuit, and if there are any, eliminate them on the spot;

(2) Adjust the front and rear brakes to ensure that the brakes are flexible and reliable;

(3) Whether the steering of the handlebar is reliable and whether the handlebar and the front fork slide each other;

(4) whether the battery socket is loose, whether the battery box lock works, and whether the horn, headlight switch and button are flexible and reliable;

(5) Whether the battery box shakes;

(6) Adjust the front and rear rims for users, and inflate the tires;

(7) Focus on checking the front and rear axle, central axle and front fork.

(8) Whether the flywheel is flexible and properly refueled.

(9) Tighten all bolts of the whole vehicle and apply antirust liquid.

(10) Teach users the experience of daily use and maintenance.

(1 1) The whole vehicle shall be cleaned and tested.

References:

Electric car? Baidu baike