Cars are a very important travel tool for everyone, so traveling by car is also necessary, but few people pay attention to their car glass, which also ensures the sealing of the car. . Recently, car editors saw a question: How is the rear windshield of a car installed? Some people also say that the car's glass is also fake. How can you tell the difference?
How to install a car rear windshield: installation process
Tools: a 50 cm wire rope; a knife or pen on a small blade; a flat-head screwdriver; a wrench; a Phillips screwdriver; pliers ; Raw materials: transparent tape, cured one-component polyurethane sealant measuring cylinder. Method/Steps First, use a flat-head screwdriver to slowly remove the black protective strip around the windshield, and then remove the protective cover under the windshield. Run a wire through the sealant under the windshield. One person is in the car and the other person is outside. Pull back and forth, slowly pulling the sealant away until all the sealant around the windshield is removed. Use a small blade to slowly scrape off the black sealant on the car, then sand it clean with sandpaper. Until the color of the iron frame is revealed. Wipe the dust around your newly purchased windshield with a rag. Apply the purchased polyurethane sealant to the frame of the car windshield, try to make it into a triangle or diamond shape, and make it as thick as possible. In order to combine well with the glass. 5. When installing the windshield, please note that there are two small brackets on the car to support the windshield, and the windshield needs to be supported on the small brackets. Squeeze slowly, then apply a layer of polyurethane sealant around the windshield and adhere the black protective strip. 6 After the installation is completed, install the wipers and lower guard, and use transparent tape to attach the windshield to the roof. It is best not to travel immediately after the completion. It is best to leave the car for two or three days until the sealant is completely set. What should you pay attention to during the disassembly and installation process? It is best to remember every process. Tools can be used flexibly or replaced by other tools.
How to install car rear windshield: How to distinguish real and fake car glass?
First, look at the glass trademarks
One is high-temperature printing and the other is low-temperature printing. The biggest difference between the two is that the low-temperature label can be removed with nails or sharp objects, while the high-temperature label cannot be removed, so the low-temperature label that can be removed must be fake glass.
Most glass trademarks contain many contents, such as manufacturer code, production date, glass properties and various safety certifications. If you don't have this information, you need to be careful that you cannot rule out fake glass. The real trademark logo on the glass has clear and uniform fonts, while the imitation logo is post-sprayed, so the fonts and patterns look rough and the edges are rough.
Second, look at the glass edges
Genuine glass manufacturers have exquisite workmanship, and the edges of each piece of glass are basically polished. The purpose of this is to make the glass look more beautiful, less likely to have cracked edges, and feel smooth and delicate to the touch. But the fake glass has rough edges and uneven edges. Even the glass produced by some small manufacturers has not even been edged. The PVB film between the laminated glass will be squeezed out, and it is possible to cut your hands when handling the glass.
Third, look at the glass mirror holder
Currently, the rearview mirrors of most models are installed on the front windshield, and the fixing device between the rearview mirror and the glass is commonly known as amp; ldquo;Mirror&rdquo. In other words, most of the original glass is already equipped with a lens holder when it is produced, which is very suitable. Most fake or factory-assisted glass is just a polished piece of glass. When replacing, the broken glass lens holder should be removed and then glued to the new glass with special glue. When you see this scene, you have to be careful. Glass without a lens holder is likely to be fake or a cheap product.
That’s it for today’s editor’s introduction. The above is a brief introduction from the car editor on how to install a car rear windshield. The glass of a car is never thought of, but it also plays a vital role. So I hope Che Editor’s introduction can solve your problem, and I also want to know more about Che Editor.
One million car purchase subsidies