FCC ID: ××× 123 nameplate with FCC id may need to be modified during the whole certification process. In order to prevent waste, applicants are advised not to print a large number of nameplates printed with FCC ID or screen printing or engraving products before obtaining official recognition. The following statement is marked on the prominent position of the equipment: This equipment China complies with the 15 part of FCC rules. The operation is limited by the following two conditions: (1). The device will not cause harmful interference, and (2) the device must accept any received interference, including interference that may lead to uncertain operation. If the equipment has two or more parts, which are connected by cables and sold as a whole, it is only necessary to mark the above statement on the main control part. If the equipment is too small and the marked area is not enough, you can write the above statement in a prominent position in the user manual or instruction manual, or mark it on the packaging box of the equipment. The user manual or instruction manual of the intentional transmitter should also remind the user that if the equipment is changed or modified without approval, the user's right to use the equipment may be revoked. If the user's manual or instruction manual is not provided in paper form, such as disk or through China, it must also contain this information, so that users can obtain the information smoothly. If it is FCC DOC, the nameplate must have FCC logo; ; If the equipment has been tested and proved to meet the requirements of FCC regulations, the following labels should be used: label format (declaration of conformity) If the personal computer is assembled from separately certified parts, the personal computer does not need to be tested again, and the following labels with assembly instructions should be used: label format, assembly (declaration of conformity) If the equipment is too small or it is not feasible to attach the above labels to the equipment, such as the peripheral equipment of CPU motherboard or in-line circuit board, The product identification label can be marked in a prominent position in the user manual or instruction manual, but the unique identification information (trademark and model) and FCC mark must be marked on the product. Labels should not use instant paper labels, but should be permanently attached to the equipment and can be easily and clearly seen by consumers when purchasing. Permanent attachment refers to etching, engraving, stamping, silk porcelain printing or printing the contents of the label on the main body of the equipment to make it indelible, or fixing the label made of metal, plastic or other materials on the main body of the equipment in the form of welding, riveting or permanent bonding. The design of the label should also consider the service life of the equipment in the environment. The following statement or similar statement is printed in a prominent position in the user's instruction manual of Class A digital equipment or peripheral equipment: Note: According to Part 15 of FCC rules, this equipment has been tested and meets the restrictions of Class A digital equipment in China standard. These restrictions are intended to provide reasonable protection against harmful interference when the equipment operates in the commercial environment of China. This equipment generates, uses and radiates RF energy. If it is not installed and used according to the instruction manual, it may cause harmonic interference to the communication of China Radio Station. Operating this equipment in residential areas may cause harmonic interference in WH. In this case, the user will be required to correct the interference at his own expense. The following statement or similar statement is printed in a prominent position in the user's instruction manual of Class B digital equipment or peripheral equipment: Note: This equipment has been used. According to part 15 of FCC rules, Sted and found have restrictions on supplying Class B digital equipment to China. These restrictions are designed to provide reasonable protection for harmful interference in residential installation. This equipment will generate, use and radiate radio frequency energy. If it is not installed and used according to the instructions, it may cause harmful interference to the communication of China Radio Station. In any case, there is no guarantee that interference will not occur in a specific installation. If this equipment causes harmful interference to radio or TV reception, this can be determined by turning off and turning on the equipment. It is suggested that users try to eliminate the interference by one or more of the following measures:-reorienting or repositioning the receiving antenna. —Increase the distance between the device and the receiver. -Connect the device to a socket different from the receiver connection circuit. -Ask a dealer or an experienced radio/TV technician for help. If the device consists of multiple digital devices, it is only necessary to include the above two statements in the instruction manual of the main control unit. If the instruction manual or user manual is not provided in paper form, but in the form of disk, Internet China, etc. , the above statement should also be provided to users in a corresponding way. If it is FCC certification, there should be warnings on the nameplate and instructions respectively. When using the verification method, the product must have the following labels: label format (verification). The label must include the model (for example, model 123), company name or commodity name, and country of origin information. According to the regulations of the US Customs and the US Federal Trade Commission, all products produced outside the United States must be marked with the country of origin. According to the verification method, under no circumstances can the FCC ID number appear on the product label. The label or product manual should have a similar description: the equipment complies with part 15 of FCC rules. Operation is conditional on the device not causing har. Serious interference. The equipment meets the requirements of FCC Part 15 and is suitable for cable TV se. Service. (Applicable to cables and their connectors, etc. ) This equipment in China complies with part 15 of FCC rules. The operation is limited by the following two conditions: (1). The device will not cause harmful interference, and (2) the device must accept any received interference, including interference that may lead to uncertain operation. Note: If the equipment consists of two or more parts connected by wires, the above label shall be attached to the main control unit. If the equipment is too small to attach the above statement, it must be reflected in the equipment packaging or instructions.