How to install Kohler toilet?
First, install the water inlet pipe and sewer pipe according to the specific size drawing, so as to be consistent with the size drawing (pit spacing must ensure the requirements of small pit spacing of the model). If you need to dismantle the old toilet, scrape off the old wax ring first. According to the installation size of the site drainage pipe and water stop valve, choose wall drainage or ground drainage to install the toilet (wall drainage requires elbow to be installed on the toilet sewage pipe on site, and ground drainage is pre-installed when leaving the factory).
2. Place the installation template on the ground, fix the installation template with adhesive tape, and drill holes on the ground with a 10mm drill bit according to the installation template. Insert the bolt sleeve into the borehole and install the bracket. Screw the water inlet pipe on the thread at the bottom of the water inlet rod of the water inlet valve.
Thirdly, the decorative cover nut is sleeved on the water inlet hose with its flat end facing outwards, and the hose passes through the hole on the side of the cylinder and extends along the toilet wall. Separate the hose clamp, put it on the inlet hose with the flat end facing outwards, close the hose clamp, insert it until it touches the toilet wall, and lock the nut.
4. Install the wax ring flange on the flange base from below. Press down, pay attention to the uniform force, and install the flange base with T-bolts. Gently lower the toilet and press it on the bracket. Press the toilet evenly, and don't move it after putting it away, so as not to damage the waterproof layer.
5. Screw the small screw into the bracket until the toilet is completely fixed. Tighten left and right alternately to prevent the toilet from deviating from the center (avoid being too tight). Install nuts and apply silicone around the toilet seat.
6. Connect the water supply pipe and turn on the water source. Remove the adhesive tape and protective pad. Press the big flush button, pull out and remove the small flush button, pull out and remove the big flush button, install the big flush button on the black flush handle, and install the small flush button on the green flush handle. Insert the flush handle into the flush button hole and clip it into place. Rinse several times, check for water leakage, adjust the water level, and then install the water tank cover and cover plate.
What should I pay attention to when installing Kohler toilet?
First, before installation, the master must first conduct a comprehensive inspection of the sewage pipeline to see if there are dirt, sand, waste paper and other sundries in the pipeline. At the same time, check whether the floor where the toilet is installed is flat. If the ground is uneven, level the ground when installing the toilet. Saw the lower drain pipe short, and make the lower drain pipe 2mm-5mm higher than the ground as far as possible when conditions permit.
Second, pay attention to check whether there is glaze at the bend. After choosing your favorite toilet appearance, don't be confused by the fancy toilet style. It is very important to see the quality of the toilet. The glaze of the toilet should be smooth and flat, without obvious defects, pinholes or lack of glaze, with clear trademarks, complete accessories and no deformation. In order to save costs, many toilets are not glazed at the bend, while others use gaskets with low elasticity and poor sealing performance. Such a toilet is easy to scale and block, and it is also easy to leak water. So when you buy it, you should put your hand into the dirty mouth of the toilet to see if it is smooth.
Thirdly, in the way of flushing, toilets on the market can be divided into siphon type and open flush type (that is, straight flush type), but siphon type is the main one at present. Siphon toilet can flush and siphon at the same time, which can quickly discharge dirt. However, the diameter of the sewer pipe of the toilet is large, and the larger dirt is easy to wash down. They have their own advantages and disadvantages, so we should consider the actual situation when purchasing.
Generally, when buying a toilet, there will be instructions on it to let us know the installation method of Kohler toilet and the matters needing attention in installing Kohler toilet. People need to be careful in the installation process after understanding it. When brand stores buy Kohler toilets, people usually install them for free, which brings great convenience to life, reduces the installation cost and is more cost-effective.