1: technical standards for garment production:

before mass production, each order must have correct and reasonable technical standards.

1. product name, order number, style number, guest name, production quantity, compilers, auditors and implementation date

2. clothing style structure diagram, including front and back finished product structure diagram, correct colors and styles of fabrics and accessories.

3. finished product specification table. (According to the guest's specifications, and the tolerance coefficient is listed for the inspector's reference).

back length: tolerance .7CM (middle of back neckline-hem edge)

bust: tolerance .7CM (normal flatness, cotton-padded jacket \ down jacket must be reduced by 1\ 2 measurement)

downward swing: tolerance .7CM (rib hem must be measured with both hands open).

Total shoulder width: tolerance .5CM (left shoulder point-right shoulder point

Sleeve length: tolerance .5CM (shoulder point-cuff)

Sleeve length: tolerance .5CM (midpoint of back neckline)

half cuff: tolerance of .3CM (rib cuff can be measured by normal flattening)

collar circumference: tolerance of .5CM (normally lower collar specification)

cutting process requirements.

1. Verify whether the sample is in conformity with the production notice and whether the number of sample pieces is in conformity with the samples

2. Whether natural ventilation is carried out according to the specified time after the arrival of the materials to ensure the correct specifications of the finished products.

3. Whether the yarn direction of each part is in accordance with the regulations of the edition, and whether the grid \ alignment \ is in accordance with the regulations of the edition.

4. Whether the eye-setting and cutting of each part are in accordance with the regulations of the edition.

5. Pay attention to the front and back sides and chromatic aberration when drawing cloth (if chromatic aberration is found, the chromatic aberration version must be arranged and the actual unit consumption must be tested and reported to the company).

6. Push the knife, and the upper and lower layers should not deviate more than .2 cm.

7. The numbering should be clear and appropriate, and the finished product should not miss the number.

5. Specifications of raw and auxiliary materials and requirements of the use parts: < p

two: the style, quality, color and specifications of raw and auxiliary materials should be carefully checked for correctness.

three: specific requirements: whether there is color difference, middle edge difference, color bar, broken yarn, defects, stains and phenomena in the fabric lining. Whether the fur does not meet the original samples or requirements in terms of width, length, color, quality and hardness.

Whether the down has color, smell, gram weight, cashmere, foreign bodies, whether there are holes in the leather, uneven thickness, incomplete dyeing, hard leather board and overall color discrepancy. Whether the adhesive liner has uneven colloidal particles, different thicknesses and unsmooth adhesion. Whether the color, quality, specifications and lettering of zipper are inconsistent with the trademark. Whether the color, specification and quality of other special accessories are in conformity with the order. Whether the trademark and other marks are in conformity with the making list

6. Sewing process requirements:

Sewing parts: The normal sewing part is 1CM, and if there is a cut, the special requirements of sewing parts should be implemented according to the size of the cut.

stitch: normally, it is 1-11 stitches for open thread every 3CM, and 9-1 stitches for concealed thread every 3CM12---14 stitches.

trademark: the normal lane should follow the color line, and if there are special requirements, it should be implemented according to the customer's regulations.

washing: the position is basically two positions. The direction of the side seam and the inner pocket should be correct.

Workmanship: the lines in all parts should be uniform, and there should be no bending, broken lines, reverse lines and disharmony between the upper and lower lines.

Pocket: square and smooth, no hair leakage in the cut, straight sewing lines, standard joints, no back warping, and symmetrical left and right positions.

the width of the zipper opening pocket should be consistent. Pay attention to the opening and cutting method, and the pocket teeth should not overlap or split. The pocket mouth of the side-attached pocket should not be less than 15.5CM for men's wear and 14 cm for women's wear.

Shoulder seam: smooth, pay attention to the direction of the shoulder arc, and there should be no distortion. Special fabrics should be bonded.

Sleeve hump: cut the seam in place in the arc to avoid the distortion of the sewing line and the penetration of the seam, and the sleeve should be put on correctly:

Pay attention to the posture of the sleeve on the sleeve hump, and keep the sleeve hill beautiful and smooth. Special fabrics should be bonded.

cuffs: smooth and untwisted, and the opening length of the cuffs should be consistent.

neckline: it should not be stretched or tightened, the inside of shoulder seam should be aligned, the seam should not be too large, and the neckline should be round and smooth)

Collar: the collar tip should not be upturned and vomited, and the size of the left and right lines should be consistent, and the looseness of the collar surface should be appropriate before using the open-cut collar seam. The seam should not be greater than .4CM

Door number: the shape must conform to the length of the paper plate, and the door number must be completed as a whole.

lining: the shape must conform to the length of the paper plate, and the doorplate must be ironed as a whole, and it can only be used after it is leveled.

hem: the sewing line can't be twisted/reversed (the looseness of the low thread should be adjusted).

lining: the cotton must be pushed into the down jacket to avoid cotton tightness.

Button.

rib: pay attention to whether the quality is correct. The specification of the finished semi-hem can be lowered by 1CM, and the specification of the finished semi-hem of elastic band can be raised by 1cm.

The top of the finished ribbed collar must be determined before production. The rib of the ribbed collar should not be too loose or too tight (pay attention to the trend of the collar *******).

Zipper: there should be no waves. Cut the zipper tape (pay attention to the cut * * * for the washing style). To stop stuttering, measure the eating amount according to the fabric performance.

Embroidery: the washing style embroidery thread must be a washing thread to avoid fading, and the color must be correct (the washing embroidery thread can only be used after being verified by washing experiments).

There must be no fading phenomenon, and washing experiments should be carried out before use. When packaging, it should be separated by copying paper to avoid mutual dyeing with the fabric.

Washing requirements:

If there is a washing style, the effect of washing must refer to the original samples of the guests and the company's confirmation opinions before batch washing.

8: Ironing process requirements:

Semi-finished products \ finished products should not have aurora \ dead pleats \ marks: pay attention to the special fabric properties, and the fabric can not be inflated to avoid deformation of the finished product specifications and styles. The ironing of the first sample must be confirmed by the company's technicians before it can be carried out (note that the washing style is not implemented according to this standard, but should be implemented according to the original sample of the guest and the effect confirmed by the company).

Packaging process requirements:

Copying paper: black antique silver metal material accessories \ fur \ tag \ tag rope \ printing \ special ingredients \ leather should be avoided from dyeing.

Plastic bags. Printing must meet the customer's standards.

Carton: the specifications must meet the height \ width \ length of the clothing (the height of the clothing should be carefully measured when the customer has special requirements), and the quality must be supervised and confirmed.

Packing: If the goods must be delivered according to the correct packing list and the customer's requirements (model number \ color \ specifications \ quantity), the factory attendant must be assigned to the destination port.