111. The methods of sheet metal correction are (AC)
A mechanical correction
B flame correction
C manual correction
D Gas correction
112. The automatic air conditioning device of a car is divided into (ABCDE) according to its function
A Refrigeration system
B Heating system
C ventilation system
D air purification system
E control system
113. Pneumatic tires with inner tubes are made of (ABCD), etc. Composition
A Inner tube
B Outer tire
C Rim
D Pad belt
114. Public Security Traffic Management The department conducts audits of driver's licenses every year in accordance with the provisions of laws and administrative regulations (C)
A conducts audits of driver's licenses every year
B conducts audits of driver's licenses from time to time
C conducts regular reviews of driver's licenses Driving license review is carried out
D carries out driving license review every six months
117. In the Lexus LS400, the torque of the engine and the braking of the driving wheels can be fully realized, which helps The system to avoid sideslip that is prone to danger when starting and accelerating is (A)
A TRC system
B ABS system
C TCS system
D Install JSPV system
118. Which of the following models is "Nissan Duke" (D)
A U13
B N16
C A32
D Y33
119. In which of the following locations do signs containing VIN code information generally appear on domestic cars (ABD)
A Left front of instrument panel shell
B Front fender
C Inside the trunk
D Inside the engine compartment
120. Thermoplastic The appearance and chemical composition of the material will not change after repeated heating and softening. It will harden after cooling. The repair method of this kind of accessory (AB)
A can be welded with a plastic welder
B The deformation can be repaired by heating with a sun lamp
C The damaged part can be melted and reshaped
D It cannot be repaired
122. Hydraulic automatic control system of automatic transmission What signals need to be accepted (ABC)
A Throttle opening
B Vehicle speed
C Wheel anti-lock signal
D Intake air temperature
124. The automobile differential is composed of (ABCD)
A side gear
B planetary gear
C Planetary gear shaft
D differential housing
E half shaft
125. Which of the following are active safety systems (BCD)
A Airbag
B Anti-lock braking system
C Braking anti-chemical system
D Electronic stability system
126. The function of the camshaft sensor is to collect the position signal of the intake camshaft and input it into the control unit to perform (BCD)
A sequential ignition control
B ignition timing control
C Explosion suppression selection control
D Injection time control
127. The automobile microcomputer control system has (ABC) control over gasoline engine emissions
A EGR exhaust gas recirculation
B Oxygen sensor and three-way catalysis
C Secondary air injection
D Activated carbon canister solenoid valve control
128.according to
According to the vehicle replacement special insurance clause A, the statement is correct (ABCE)
A Additional insurance for vehicle loss insurance
B has insured vehicle loss insurance and commercial third party liability insurance
C Select the accident liability deductible rate as "without deductible"
G The time when the insurance was purchased is less than 2 years from the initial registration time
E Vehicle loss insurance If the accident causes vehicle damage, the repair cost will reach the purchase price of a similar new car when the insured accident occurred
129. The following understanding of the average compensation per unit in the fiscal year is correct ( )
A (This article Monthly settled claims + pending claims increment)/number of insured items
B reflects the dynamic changes in claim flow relative to the number of policies
C When the business scale is relatively stable, the average claim amount per policy Changes can reflect changes in the level of claims quality
D This indicator data is calculated from PCIS underwriting claims reports to motorcycles
E On the basis of a relatively stable underwriting structure, through this Comparing the indicators with the historical period of the policy in the previous two years, we can observe the changes in claim quality
130. Advantages of gas-filled shock absorbers (BCD) compared with twin-tube shock absorbers
A Simplified structure and reduced mass
B Reduce wheel vibration when subjected to sudden impact
C Greater damping force and higher working reliability
D The high-pressure gas and oil inside the shock absorber are separated by the floating piston
131. Common problems of automobile braking systems (AB)
A deviation
B Drag
C Failure
D Failure
132. The standard voltage of the Vc terminal of the vacuum sensor of the intake manifold is (B) V, (Take JZS133 series as an example)
A 8……10
B 5 _0.5
C 2……4
D 12
133. Which of the following (D) does not belong to the components of automobile air conditioning system
A compressor
B condenser
C Evaporator
D Unloading valve
134. The maximum gradeability of a car is (C)
A On a good road surface, when the first gear is unloaded Maximum gradient
B Maximum gradient with direct gear on good road surface
C Maximum gradient with maximum speed of the car on good road surface
D Good On the road, the maximum gradeability of the full cabin and first gear is 135. (C) The suspension is a suspension in which the wheels move up and down along the swinging kingpin axis
A double trailing arm type
B double wishbone type
C candle type
D MacPherson type
136. The rear windshield of Santana car is ( A)
A tempered glass
B laminated glass
C organic glass
D insulating glass
137 .As one of the basic signals for determining the fuel injection amount, the air flow meter mainly uses the (A) type EFI system
A L
B D
C E
p>D F
138. The slip rate range in which a car can achieve the best braking effect is (C)
A 10-20
B 15-20
C 15-25
D 25-30
139. "Road Traffic Safety Law" regarding passenger carrying regulations for highway passenger vehicles : When the number of passengers is full, the number of children free of charge according to regulations shall not exceed the approved number of passengers (D)
A20%
B15%
C5%
D10%
140. When evidence may be lost or difficult to obtain in the future, litigation participants may apply to the People’s Court (B)
A Detain the client
B Preserve the evidence
C Restrict the client's personal freedom
D Freeze the property
142. The multiple accident exemption rate selected in the vehicle 07 clause will increase by 5% each time starting from the (C) time
A two
B three
C Four
D Five
143. According to Article 16 of the "Regulations for the Implementation of the Road Traffic Safety Law", passenger vehicles in operation shall be inspected once a year within 5 years. If they exceed 5 years, (A) Test once
A half year
B1 year
C quarterly
D2 year
145. A person without the ability to litigate shall have his guardian serve as his legal agent to litigate on his behalf, and the legal agents will shirk their agency responsibilities (D)
A The public security organ may detain a guardian who refuses to perform his or her obligations
A p>
B The People's Court shall determine a person to litigate on its behalf through forced negotiation
C The People's Procuratorate shall litigate on its behalf
D The People's Court shall appoint one of its persons to litigate on its behalf
146. Which of the following does the Santana 2000 electronically controlled gasoline injection engine belong to (D)
A Multi-point injection intake pressure sensing open-loop control
B Single-point injection injection Closed-loop control of air pressure sensing
C Combined closed-loop and open-loop control of multi-point injection intake air flow sensing
D Combined closed-loop and open-loop control of multi-point injection intake pressure sensing
147. Our company stipulates that automobile maintenance hours are based on prices in Class II areas, and the maximum price limit for Class II enterprises operating in Class II areas is (B) yuan/hour
A100
B80
C60
D40
148. Components that must be replaced during automobile engine overhaul (D)
A piston
C connecting rod
C valve
D cylinder gasket
149. Radiator repair using (C) process welding
A arc welding
B resistance welding
C brazing
D friction welding
150. At present, my country The first unused number among the four Arabic numerals in the middle of the domestic car model is (C)
A1
B3
C8
D9
151. The types of drive axles include (BC) form
A connected type
B disconnected type
C Non-disconnecting type
D overlapping type
153. In L type EFI, when the engine is started and enriched, the initial correction value of the fuel injection amount is determined based on (ABD)
A Cooling water temperature
B Engine speed
C Throttle position
D Intake air temperature
154. Toyota model code UCF20L-AEPGKW, the model it represents (B)
A Toyota Camry 3.0
B Toyota Lexus 4.0
C Toyota Crown 3.0
D Toyota Crown 2.8
155. The statement about abandoning turbocharging is correct (ABC)
A uses the energy of engine exhaust
B Introduce part of the exhaust gas into the combustion chamber for re-combustion
C Increase the engine air intake per unit time
D Drive through the crankshaft belt theory
156. Composition of the engine air intake system (AB)
A Air filter
B Intake manifold
C Carbon canister
D Drying Bottle
157. When the car is driving, when the driver turns the steering wheel left or right, he feels heavy and laborious, and has no sense of rightness. When the car turns at a low speed,
When turning around, the steering wheel is hard to brake, which may cause the above problems (ABCD)
A Insufficient tire pressure
B Excessive kingpin caster angle and excessive inclination
C Deformation of the front beam and frame causes misalignment of the front wheels
D No oil or oil leakage in the steering gear
158. Manifestations of false documents for insurance fraud Main features of the form (ABCDE)
The document provided by A has many modifications, and the signing time is concentrated
The document B is incomplete, unusually complete or unclear
C The witness has a close relationship with the insured or the relevant parties or insiders are missing or out of town
D The document notes are similar or the invoice serial number
E refuses to form a written transcript, only Choose to contact the insurance company orally or by phone
160. Basic principles of contract law (BCD)
A. The principle of freedom of contract
B. The principle of good faith
C Principle of Legality
D Principle of Encouraging Transactions
161. According to the provisions of the Civil Procedure Law, effective rulings, rulings, errors or illegal mediation should be retried (AB C EF)
A There is new evidence that is sufficient to overturn the original judgment
B The original judgment and the main evidence for the facts found in the ruling are insufficient
C The original judgment , The law used in the ruling is incorrect
D The people's court violated legal procedures, which may affect the correct judgment and award of the case
E The judges were hearing the case.
Corruption and bribery
F can provide evidence to prove that mediation violates the principle of voluntariness or the content of the mediation agreement violates the law
162. The job positions involved in the auto insurance claims operation specifications are (ABCD)
A95512 call center agent
B full-time price verification post, full-time loss verification post
C claims quality audit post
D guide Post, repair post, claim verification post
E Auto Insurance Claims Service Center Management Post
164. FAW Toyota has several production bases in China (C)
A1
B2
C3
D4
165. The front windshield glass of a car was broken into spider web cracks and fragments If they are still bonded together, the forward glass belongs to (D)
A tempered glass
B crystal glass
C frosted glass
D laminated glass
166. The model below is produced by Opel Car Company (AB)
A 95
B OMEGA
C ELANTRA
D LANCER
167. When the air conditioner is not turned on, a normal car idles normally (A)
A 700
B 1200
C 1600
D 2000
169. The following (C) is not a model produced by Shanghai Volkswagen
A Passat
B Goul
C Caddy
D Santana
170. The main reason for a car to flick when braking (C )
A Braking too quickly
B The braking force of the left and right rear wheels is unbalanced
C The rear wheels lock up before the front wheels
D The front wheel locks up before the rear wheel
171. The fastest number of times to adjust the valve clearance of a four-stroke engine (B)
A1
B2
C3
D4
173. The ABS of Dongfeng Honda Civic uses (A) control method
A four-sensor four Channel/Four-wheel independent
B Four-sensor three-channel/Front wheel independent-rear wheel low selection
C Three-sensor three-channel/Front wheel independent-Rear wheel low selection
175. Principles to be followed when engaging in insurance activities (ABDE)
A Voluntary
B Respect for social merit
C The insurer’s interests are the greatest
D Comply with administrative regulations
E Comply with the law
176. Fast case approval set (AB) integrated
A Validation
B Loss verification
C Compensation verification
D Repair
177. Wrong statement about compulsory traffic insurance (ABCDE)
A Among the various limits of compulsory insurance, the no-liability limit is 50% of the applicable limits
B The motor vehicle management department can register motor vehicles that have not participated in compulsory insurance. Motor vehicle safety technology The inspection agency shall conduct the inspection, but the owner of the motor vehicle must purchase compulsory insurance within the specified time
C When the ownership of the motor vehicle is transferred, the procedures for canceling the compulsory insurance contract must be completed
D Compulsory traffic insurance compensation processing When doing so, the principle of no-fault compensation is adopted
E In order to fully protect the interests of the victim, a motor vehicle can be insured with multiple insurance policies at the same time
179. The following motor vehicle conditions must be changed and must be changed (ABC)
A Body color
B Change body
C Change body or frame
D Change rearview mirror model
180. Which of the following statements is correct (CD)
A When the height of the cargo carried by a motor vehicle exceeds the carriage rail, no people are allowed on the cargo
B Tractors and battery trucks , When wheeled special vehicles are driven on ice, snow, and muddy roads,
It shall not exceed 20 km/h
C Medium-sized medium-sized trucks and semi-trailers shall not carry goods more than 4 meters in height from the ground
D Motorcycles shall carry goods in a height not exceeding 4 meters from the ground 1.5 meters
E On urban roads, a freight motor vehicle can carry 1 to 3 temporary workers in the carriage as long as a safe position is left.
181. Compared with the steel body of a car, the description of the characteristics of Audi's aluminum body frame is correct (ABD)
A The body weight is lighter
B It is less likely to rust
C The repair cost after a collision is lower
D There are fewer welding points during manufacturing
182. According to the different physical properties of the automobile sheet metal welding process, the welding method can Summed up as (ABCD)
A fusion welding
B pressure welding
C brazing
D ultrasonic welding
183. As of 2006, which of the following domestic car model series include HUD (head-up display system) as standard configuration (AC)
A Dongfeng Nissan Bluebird
B FAW-Volkswagen Jetta
C Shanghai GM Regal
D Shanghai Volkswagen Santana
184. The correct thing about car repair is (CD)
A four Wheel suspension can ensure the accuracy of four-wheel positioning
B Refreshing engine oil generally requires replacing the oil filter element
C When welding a car body, the negative electrode of the battery should be disconnected first
D Should not attempt to detect the airbag igniter resistance
185. The prestressed skin of modern buses is generally fixed to the body frame using the (AD) method
A Electric welding
B willow welding
C bolt connection
D bonding
186. The three-way catalytic reactor can synthesize the Treatment (ABD)
A CO
B NOX
C CO2
D HC
187. Investigation The purpose of the recent repair and maintenance of a burned car is (AD)
A. To understand whether the fire is related to improper maintenance
B. To determine whether the insured has an insurable interest
C Evaluate the condition and actual value of the vehicle
D Determine whether the vehicle caught fire under dynamic or static conditions
188. Basic performance indicators of the car (ABC)
A Power Performance, fuel economy
B Braking performance, operating stability
C Ride performance, passability
D Acceleration, maximum gradeability
p>
190. The "Operation Standards for Auto Insurance Loss Assessment and Valuation" stipulates the photo principle (ABCD)
A takes a photo of the entire vehicle first and then a full photo of the scene
B takes a photo first Photograph the original state and then the changed state
C Photograph the traces on the vehicle first and then photograph the traces on the road at the scene
D Photograph the easily damaged and disappearing first, then photograph the less likely to be destroyed
191. The crank connecting rod mechanism is composed of (ABC)
A body group
B piston connecting rod group
C crankshaft flywheel group
p>D cylinder group
192. For the loss of vehicle parts in an accident, the general principle of "mainly repairing can be repaired or not replaced" should be grasped. In the actual loss determination process, the specific principles should be grasped ( ABCD)
A For those that neither affect the performance nor the appearance quality, and can be restored using simple processes, repairs should be the main thing
B maintenance enterprises of Category II or above If the technical level cannot be repaired or the workmanship cannot guarantee the quality after repair, it should be replaced
C When the repair cost of the accessory exceeds or is equal to the replacement cost of the accessory, it should be replaced
D All replacement parts are fixed The damage specifications shall not be higher than the brand and specifications of the original vehicle assembled before the accident
193. Engines can be divided into cooling methods (BC)
A oil cooling
Engine
B Air-cooled engine
C Water-cooled engine
194 Repair method of bending deformation (ABCD)
A Repair of body structure Pull out the overall deformation and indirect losses on the sheet metal parts
B Level the surface of the sheet metal parts, especially the impact points with direct damage
C Since the impact damage is not very serious Even if there is no overall deformation of the car body, the indirect damage must be repaired, and then the direct damaged part should be repaired
D If there is torsional deformation in the indirect damage, pull and flatten it first, and then perform flattening work on the twisted part , and after the elastic deformation is restored, the directly damaged impact point is leveled
195. Damage to the valve includes (ABCD)
Bending of the A rod
B Rod wear
C Rod end wear
D Head working surface wear
196. Advantages of automotive electronic anti-lock braking system ABS (ABCD)
A Maintain directional stability when braking
B Maintain steering control ability when braking
C Shorten the braking distance
D Reduce tire wear
E Reduce driver tension
198. EFI engines can be divided into (AB) according to the gasoline injection position
A cylinder Internal injection
B Intake pipe injection
C Multi-point injection
D Single-point injection
199. Mechanical engineering materials include (AB )
A metal material
B non-metal material
C composite material
D rigid material
200 .Hand tools for automobile sheet metal repair are divided into two categories (AB)
A general tools
B special tools
C special tools
202. The throttle position sensor is installed on the valve body to detect the opening of the valve. Common throttle types (AB)
A switch contact throttle sensor
B Linear variable resistor throttle sensor
C Comprehensive throttle position sensor
D Throttle position sensor for automatic transmission control system
203. Compared with the reciprocating piston engine block, which parts of the engine only perform linear reciprocating motion (AC)
A piston
B connecting rod
C intake valve
D flywheel
205. The electromagnetic clutch is used to control the compressor in the refrigeration system. There are (AD) types of electromagnetic clutch
A rotating coil type
B Fixed coil type
C One-way coil type
D Multi-directional coil type
206. Automatically verify the price after investigating the case Conditions (ABD)
A The amount of damage to a single vehicle is less than or equal to the surveyor's on-site damage assessment limit
B The surveyor's single standard unsystematic price quotation limit for accessories is less than or equal to the set price
C The sum of the reported amounts of system quoted accessories is not greater than the sum of the system manufacturer’s guide prices
D The sum of customized bicycle accessories is less than or equal to the set value
207. The engine hood can generally be adjusted through (AC) adjustment
A hinge
B adjustable positioner
C engine hood hook
D The cable of the engine hood
208. In the operation specification of damage assessment (ABCD), both the accident photos and the vehicle frame number rubbings must be provided
A The entire car was damaged
B Burnt car
C Flooded car
D The total loss in the accident is expected to exceed 10,000
209. Under maintenance When replacing an engine, what hours of work are involved in replacing the engine cover (ABCD)
A. Cleaning the air valve seat
B. Grinding the valve
C. Grinding the cylinder head to match the cylinder block Surface burrs
D Clean the valve cover water jacket<
/p>
210. Automobile sheet metal manual forming process includes (ABC)
A Bending, placing and closing
B Pulling, arching and curling
C Hinge, reinforcement, correction
D Grinding, polishing
212. Although the suspension of modern automobiles has various structural forms, it is generally composed of Composed of three parts (BCD)
A wheel
B elastic element
C shock absorber
D guide mechanism
213. Scratches and cracks on automobile plastic parts are usually repaired by (ABCD)
A. Use clean water or plastic cleaning agent to wipe the repaired part and clean the oil on the joint surface
B. Cleaning Before post-bonding, heat the plastic parts, spray the catalyst to the crack side, and then use the adhesive as shown in the picture
C is flame treated at the bonding area to improve the adhesion
D. Rapidly press the scratches or cracks and then harden them
215. The main performance index of gasoline is (BD)
A. Evaporation
B. Resistance Explosiveness
C Low-temperature fluidity
D Calorific value
216. If an insured motor vehicle suffers an insured accident, the insured shall apply to the insurer for compensation. When making a claim for insurance money, the insured should submit (ABCDE) materials to the insurer
A. Accident certificate issued by the management department of the public security organ
B. Relevant documents issued by the People’s Court and other institutions Legal documents and other certificates
C Valid identity certificates of the insured and the victim
D Proof of the victim’s property loss, personal disability, relevant medical certificates and relevant List of losses and list of expenses
E Driving license of the insured motor vehicle and driver’s license
217. Article 24 of the "Compulsory Insurance Clauses for Motor Vehicle Traffic Accident Liability", (ABD) situation, the rescue fund will advance the rescue expenses
A The rescue expenses exceed the liability limit of the compulsory traffic insurance insurance
B The motor vehicle involved in the accident does not participate in the compulsory traffic insurance insurance
C The driver is not qualified to drive
D The motor vehicle escapes after a hit and run
219. Which of the following are exempt from natural loss insurance (ABD)
A Losses caused by violations of vehicle safety operating rules due to manual direct fuel supply, high-temperature baking, etc. during the use of the vehicle by the insurer
B due to natural causes only losses to circuits, lines, and fuel supply systems
C Burning of the entire vehicle caused by nature while carrying goods
D Loss of the insured vehicle caused by the insured’s intentional or illegal behavior
220. Model represented by Honda Motor JHMKA96400C000001 (D)
A Honda Accord
B Honda Citizen
C Honda CRV Jeep
D Honda Mileage
221. The following measures should be taken to check the deformation of automobile parts (D)
A. Measurement of axial direction and axial runout
B. Measurement of flatness and symmetry
C Dynamic Balance Detection
D or above are acceptable
222. The English abbreviation of the driving force control system (D)
A ABS
B TDC
C ECU
D TRC
223. In order to be separated from other wiring harnesses, the electronically controlled automobile airbag wiring harness is generally (C)
A Red
B Blue
C Yellow
D Black
224. BMW vehicle accessories In the accessories CD, only the last part of the VIN code (D) is needed
A 4
B 5
C 6
D 7
225. The fault code stored in the car computer can be read with (C)
A test light<
/p>
B digital multimeter
C oscilloscope
D mechanical multimeter
226. The ASR (TRC) system is in the car (C) state Functional
A Normal startup
B High-speed driving process
C Starting acceleration process
227. About automobile chassis parts The assembly relationship between them, the following (D) is correct
A There is an interference fit between the transmission shift fork shaft and the transmission cover
B Between the transmission shift fork shaft and the transmission cover It is fixed with bolts
The shift fork on the C transmission is fixed with bolts between the shift fork shafts
The shift fork on the D transmission is fixed between the shift fork shafts. Clearance fit
228. (D) of the automobile air conditioner can separate the gas in the refrigerant liquid and filter out the impurities
A compressor
B Condenser
C expansion bottle
D drying bottle
230. The device does not belong to the air supply system (ABD) in the electronically controlled fuel injection system
A air filter
B throttle body
C engine speed sensor
D air flow device
231 .The motors of domestic cars are generally (C)
A air-cooled type
B water-cooled type
C does not require cooling
232. Diesel fuel grades are divided according to (D)
A Pyrophoricity
B Evaporation
C Viscosity
D Condensation Point
233. The following is not the transmission assembly overhaul sign (ABCD)
A The transmission shaft and gears are severely worn
B The transmission oil seal is damaged
p>
C Transmission bearing hole wear exceeds the limit
D Transmission housing rupture
234. As the engine compression ratio increases, the inflation coefficient (B)
A increases
B decreases
C remains unchanged
D increases first and then decreases
235. Dongfeng EQ1090E The steering gear form of a type car is (B)
A rack and pinion type
B recirculating ball type
C worm crank finger pin type
D worm gear type
236. When determining the damage of the accident vehicle, the damage assessment personnel should work with (D) to assess the damage of the accident vehicle within the specified time, and A determine the repair price
B Adjustment Company
C Price Bureau
D Insured
E Repair shop
238. Acceleration ability of automobiles Commonly used (C) means
A starting acceleration time
B overtaking acceleration time
C A and b
D acceleration
p>
239. Which of the following devices does not belong to the electronically controlled fuel injection system (A)
A air flow meter
B unloading oil
C Oil pressure regulator
D fuel injector
240. The motor vehicle used on the road does not have a motor vehicle license plate, does not have an inspection mark, or does not carry a driving license or driving license with the vehicle. The public security and traffic management department (B) may impose penalties in accordance with regulations.
A may detain the motor vehicle, notify the party concerned to provide the corresponding license plate, mark, or go through the corresponding formalities
B shall detain the motor vehicle, notify the party concerned to provide the corresponding license plate, mark, or go through the corresponding formalities.
C notifies the party concerned to provide the corresponding license plates, signs or re-applies the corresponding procedures, and the party may be detained
D. Notifies the party concerned to provide the corresponding license plates, signs or re-applies the corresponding procedures, but the motor vehicle cannot be detained
241. When the People’s Court hears voter qualification cases, cases of declaration of disappearance or death, cases of determining that a citizen has no capacity for civil conduct or has limited capacity for civil conduct, and cases of determining that property has no owner, the People’s Court shall use this Article. If there is no provision in this Chapter, Use (B) and other relevant provisions of the law
A Simple procedures
B Special procedures
C Ordinary procedures
D Difficult cases Procedure
243. Motor vehicles that are used legally after registration shall undergo regular safety technical inspections in accordance with the provisions of laws and administrative regulations and based on different circumstances such as vehicle purpose, number of passengers and cargo, and service life. . For (C), the motor vehicle safety technical inspection agency shall conduct the inspection, and no unit shall impose other conditions. For vehicles that meet national motor vehicle standards, the traffic management department of the public security organ shall issue an inspection certificate.
A provides a motor vehicle driving license
B provides a motor vehicle driving license and a driving license
C provides a motor vehicle driving license and third party liability enforcement for motor vehicles Insurance policy
D provides compulsory motor vehicle third party liability insurance policy
245. According to the law, both parties voluntarily reach a written arbitration agreement on contract disputes and apply for arbitration to an arbitration institution. If a lawsuit is filed in the People's Court, (C)
The court can accept the application of plaintiff A
B informs the plaintiff to apply for arbitration to the arbitration institution, and the people's court can accept it at the same time
C informs the plaintiff to apply for arbitration to the arbitration institution
The court can accept the defendant's application
247. The automobile air-conditioning refrigerant Freon R12 contains (D) causing damage to the ozone layer Destruction
A Sulfur
B Fluorine
C CO2
D CL
248. The parties involved in the traffic accident If you are not satisfied with the determination of responsibility, you can apply for re-determination on the date of receipt of the determination of responsibility (A)
A 15
B 30
C 10
D 20
249. The insurance company shall, within (D) days from the date of receipt of the certificates and information provided by the insured, determine whether it is covered by insurance liability and notify the insured of the result. Insurer
A 3
B 1
C 10
D 5
250. Characteristics of risk (ABC)
A Objectivity
B Damage
C Uncertainty
D Regularity
E Development
251. What are the common denials of compensation (ABCDE)
A The vehicle involved in the accident is not an insured vehicle or the time of accident is outside the insurance period, etc. It is not within the scope of insurance liability. Accident
B The accident was caused by the insured’s intentional or illegal behavior
C The insured failed to truthfully declare the condition of the insured vehicle and was therefore in danger
D After an insured accident occurs, the insured fails to notify the insurer within the specified time despite the conditions, causing the cause of the accident, division of responsibilities, etc. to be unable to be determined
E fails to make a claim within the specified time, or fails to comply with the prescribed time limit Provide necessary documents, or forge documents to obtain claims by fraud
252. Regarding the statement that the contract is invalid, which of the following are correct (ABCD)
Party A used fraud and coercion Entering into a contract and harming national interests
B Covering illegal purposes in legal forms
C harming the interests of the public ***
D A person without the right to dispose of others. property, which has been ratified by the right holder or the person without the right to dispose has obtained the right to dispose of it after entering into a contract
253. Cause of over-steering of the car (ABCD)
A steering gear bearing has been assembled Tight
B Front axle or frame is bent and deformed
C Steering device is poorly lubricated
D Toe-in is too large
254. When taking notes in a robbery case, attention should be paid to (ABCD)
A. The relationship between the accident driver and the insured
B. Whether there are operational activities or economic disputes and whether these two situations are related to It is directly related to the theft of this car
C Whether the procedures for the car are complete
D Whether there is someone to charge the car at the place where the car was lost, and whether there is a fee receipt
255. None Advantages of distributor ignition (ABCE)
A Ignition advance is controlled by computer, which is more flexible and accurate
B Improves the control accuracy of ignition advance angle
C Ignition The spark energy is increased by 14% and the electromagnetic wave radiation interference is effectively reduced
D The ignition system is expensive
E Maintenance-free and no high-speed initial ignition advance angle is required
256.The model code of the 2003 Toyota Overlord (D
)
A ACV30
B UZJ100
C TCR10
D ACR30
257. In order to improve the performance of the engine Idle stability, ECU corrects the fuel injection amount according to the absolute pressure of the intake pipe (AD)
A Intake air temperature
B Engine idle speed
Section C Valve opening
D Cooling water temperature
258. The automobile airbag system belongs to (B) safety system
A automatic
B passive
C Preventive
D Remedial
259. The role of intercooler (D)
A Cooling engine coolant
B Cools the air conditioning refrigerant
C Cools the power steering pump oil
D Cools the pressurized air
260. Frame Vertical and horizontal beams must not be severely bent. When using segmented testing, the diagonal length of each segment should be less than (B)
A 3 mm
B 5 mm
C 7 mm
D 8 mm
261. Which of the following functions cannot be achieved by car glass film (D)
A heat insulation
B Anti-riot
C Resist ultraviolet rays
D Reduce noise
262. Full-time four-wheel drive ***has (C) differential
A1
B2
C3
D4
264. The car named Fengdu in Chinese is produced by (C) Company
A Toyota Motor
B Honda Motor
C Nissan Motor
D Mitsubishi Motors
266. Insurance Vehicles The loss that occurs within the scope of insurance liability shall be compensated by a third party. If the third party cannot be found, the insurer shall compensate. (C)
A The insured must provide witnesses who have no relationship with the third party. Evidence and physical evidence
B The insured must provide evidence of eyewitnesses who have no relationship with the insured
C For accidents that occur on the road, the certificate identified and issued by the traffic management department shall prevail. In other cases Accidents that occur at the site shall be subject to the certificate issued by the local public security department
D The insured must provide physical evidence
268. Which of the following expenses can be compensated by the insurance company after a vehicle accident (AD)
A Reasonable transportation costs for the rescue company to tow the car to the repair shop Transportation costs
B Expanded losses caused by improper rescue
C Caused by rescue Losses caused by loss of personal belongings
D Reasonable expenses for hiring a guard if the insured vehicle is unable to be driven after being injured
E Cost of rescuing goods loaded on the damaged insured vehicle
269. Which of the following words about cars means steering knuckle (D)
A Steering wheel
B Steering gear
C Disc wheel
D Steering knuckle
270.VSS is the English abbreviation of (B)
A idle speed control valve
B vehicle speed sensor
C shift solenoid valve
D crankshaft position sensor
272. Our company’s principle for determining parts management fees (AC)
A According to the maintenance shop technology The category and specially repaired vehicles shall be determined after comprehensive consideration
B Vehicles repaired at professional repair stations may be subject to an additional 15% management fee
C All management fees that need to be added must be approved by the head office
p>D As long as the head office confirms the price and cannot buy the accessories locally, the management fee can be increased
273. Which of the following parts does the three-component integrated hydraulic torque converter consist of (ACD)
A pump wheel
B idler wheel
C turbine
D guide wheel
274. The moment when the planetary gear differential takes effect (A)
A Car turns
B Drives in a straight line
C Car turns and drives in a straight line.
275. The driven part of the clutch includes (CD)
A flywheel
B clutch cover
C driven plate
D friction plate
279. Notary agency completed The time limit for notarization is (C)
A Within one month from the date of application
B Within one month from the date of acceptance
C From submission Within one month from the date of application
D Within six months from the date of submission of application
284. Which of the following characteristics does a good paint surface layer have (BDE)
A Adhesion
B Anti-rust and imitation properties
C Thickening
D Ease of grinding
E Maintain color properties
288. Automatic transmissions generally use (AC) to brake the planetary gear mechanism
A band brake
B internal tension drum type Brake
C Wet multi-disk brake
D Floating caliper disc brake