I. Preparatory work

1, black ink cartridge, lift the sticker on it and make a hole. 2. Color ink cartridge with three holes after removing the sticker.

3. Enlarge the ink hole with a small drill, subject to the needle tube.

4. Add 6-8ML to black and 3-4ML to each color. Please be careful not to cross colors. 5, please grasp the strength when drilling, the hole is not particularly good to drill, but when you really want to drill, don't use too much force. 6, whether drilling or adding ink, please try not to touch the ink cartridge chip and nozzle.

Note: Do not add ink too quickly to avoid overflow, and the amount should be moderate. If you add too much ink, it will not only lead to ink leakage, but also overflow ink is likely to wet the parts and affect the appearance. If you add too much ink, please gently touch the ink cartridge and print head with a soft paper towel to absorb the excess ink.

There is a sponge in the ink box. Please stay 1 hour after adding ink before printing, so that the ink can be fully soaked. Before printing, it is best to use the printer's own cleaning program to clean it 2-3 times.

Second, the inking step

1. Follow the correct steps to remove the ink cartridge.

2. Lift the label on the ink cartridge to expose the ink adding hole.

3. Enlarge the ink hole with a tool and add ink according to the color. If there is ink left in the tank like an earthworm, please suck it up with a paper towel.

4. Stick the label back as it is, put it in the printer, and print it after 1 hour. Be careful not to cover the pores. In addition, if there is ink residue in the wormlike slot, please suck it up with a paper towel, otherwise it will not print.

Question 2: How to fill the color ink cartridge of Canon printer? Go and buy a set of special ink for Canon printer, in four colors of CMYK, and use the matching drill to enlarge the pores seen by tearing off the label cartridge, and then you can charge it. One hole in black, three holes in color, red on the top, blue on the left and yellow on the right. If you are afraid of making a mistake, insert the toothpick into the hole to see what color it is, and add about 5ml. Finally, it is OK to wrap it with tape.

Question 3: How to add ink to Canon ink cartridges? There is a small hole in the PG880 paper on the ink cartridge. Enlarge and add ink with scissors. A color of 3ML black can add 5ML, no more. After adding a computer, you will still be prompted that there is not enough ink. Or used up. As long as it can be used normally, don't pay attention to its prompt.

Question 4: How to add ink to Canon printer? Where can I see the display? If I can type it, I won't have to worry. Just install the print head and take photos, and I don't need to look at anything else. . Hmm. How interesting

Question 5: How to fill the Canon cli-85 1 ink cartridge? Take off the black ink cartridge, tear off the label on the ink cartridge, and punch holes in the middle, and the color will be the same. After you tear off the label, there are three circles on it. Just punch holes in it. The top is red, the bottom is yellow and blue. If you are not sure, just insert a toothpick to see what color it is, and then seal the hole.

Question 6: How to add ink and tear off the label of Canon mg2980 ink cartridge? When you see a hole the size of a small needle eye, drill the hole bigger with a small drill bit and inject ink with an ink injector.

Generally, about 5 ml of ink is enough for this standard volume. After adding ink, it is better to clean it twice with the cleaning function in the driver before printing.

If you are satisfied, please adopt it!

weijiabgyp.tmall/

Question 7: How to add ink A to Canon ip2780? 1. Carefully heat the sticker on the ink cartridge with a hair dryer or a blade, then uncover or tear it off and stick it neatly on the side of the ink cartridge for future identification.

2. Use a special drill to drill the ink injection hole of the ink cartridge. If there are ink injection holes in the ink cartridge, there is no need to drill holes (such as HP8 16/8 17 series ink cartridges). For example, Canon 830/83 1 series ink cartridges have ink injection holes, but they need to be drilled. Be careful not to drill the whole hole when drilling to prevent the air pressure from being too high in the later period.

3. Insert the needle cylinder into the ink injection hole, draw out a little ink or directly look at the color on the needle tip to confirm the color of the ink injection hole of each ink cartridge. Be sure to look carefully to prevent the ink cartridge from being scrapped because of adding the wrong ink color.

4. Use a syringe to suck ink from the ink bottle. If you use spring bottle ink, you can directly use it to fill the ink cartridge. When injecting ink, please insert the syringe into the ink injection hole at a 45-degree angle, and then slowly inject ink. The purpose of slow injection is to minimize the generation of bubbles. Pay attention to stop the ink injection when the ink is full and about to overflow, and let it stand for a few minutes before repeating. (Note: Every color is operated in this way. In order to prevent the nozzle from leaking ink during inkjet, the nozzle can be wrapped tightly with plastic wrap. )

5. If there is an ink suction fixture, please insert the ink cartridge into the ink suction fixture, find a rubber plug to block the hole at the bottom of the ink suction fixture, and then add ink as above.

6. In the absence of an ink suction fixture, turn the ink box upside down for about ten minutes after placing the ink; There is an ink absorption fixture, and then use it to absorb ink. The method is: clamp the ink cartridge in the ink suction fixture, use a needle tube without a needle tip in the ink suction hole at the bottom of the ink suction fixture, and insert it as tightly as possible! Pump the air out of the ink box, and the amount of ink pumped out is about 0.5 ml. Then carefully remove the ink cartridge from the ink suction fixture, carefully dip the ink on the surface of the nozzle with a clean napkin until you see three neat colors, and then print on the computer. Pay attention to cleaning the used ink suction fixture and syringe, and put them away for next use!

The 2780 you used is the same as the 830/83 1 ink cartridge method mentioned in the second article of my article.

Question 8: How to add ink to Canon ink cartridges Canon original independent ink cartridges can add ink. Remove the trademark tape from the ink bin end of the ink cartridge, and you will see that the ink injection port is sealed with plastic balls. Pick out the ball with two big sewing needles, and you can add ink, and you can add it with a syringe. When adding ink, be sure to block the ink outlet at the lower end, otherwise it will flow everywhere. Just seal your mouth with a soft plastic plug after adding ink. Canon's independent ink cartridges are generally like this. But it's better to replace the chip on the ink cartridge with a permanent one, otherwise it's still a little uncomfortable to use.

Question 9: How to add ink to Canon ink cartridges? Is it an original ink cartridge? It is best not to add ink.

In order not to add ink, manufacturers have counting chips on ink cartridges. Even if you add ink, you can't print a few.

You can replace the ink cartridge with an easy-to-add ink cartridge, and then add ink.

Easy-to-add ink cartridges can print about 800 sheets at a time, and can be added many times until the print head is scrapped.

Of course, the method of adding ink is also very simple, just a syringe.

Like us, we usually only play things at home occasionally, and basically we just need to buy ink in the future.

Zhengzhou Weike Electronics has changed well, which reminds me of many small details. Nice guy.

Question 10: How to fill the ink cartridge of Canon ip 1 180 printer? Add ink for 20 minutes. See the picture.

1, black ink cartridge, lift the sticker on it and make a hole.

2. Color ink cartridge with three holes after removing the sticker.

3. Enlarge the ink hole with a small drill, subject to the needle tube. We will send a small drilling rig.

4. Add 6-8ML to black and 3-4ML to each color. Please be careful not to cross colors.

5, please grasp the strength when drilling, the hole is not particularly good to drill, but when you really want to drill, don't use too much force. 6, whether drilling or adding ink, please try not to touch the ink cartridge chip and nozzle.

Note: Do not add ink too quickly to avoid overflow, and the amount should be moderate. If you add too much ink, it will not only lead to ink leakage, but also overflow ink is likely to wet the parts and affect the appearance. If you add too much ink, please gently touch the ink cartridge and print head with a soft paper towel to absorb the excess ink.

There is a sponge in the ink box. Please stay 1 hour after adding ink before printing, so that the ink can be fully soaked. Before printing, it is best to use the printer's own cleaning program to clean it 2-3 times.