How can I make my ballpoint pen write more smoothly?

Methods to make ballpoint pen writing smoother

1. We can solve the problem of ballpoint pen not writing smoothly once and for all by doing a little work on the ballpoint pen refill.

2. Find a thicker needle or pin, and poke a small hole through the ballpoint pen refill about 1 cm above the oil level. If the ballpoint pen refill is not writing smoothly, you can refill it. Got on duty and made a difference.

Use common sense

1. This pen is stronger and more durable than ordinary pens, but if it is used and stored improperly, it is often impossible to write. This is mainly due to the dry ink adhesion. This is because it blocks the flow of ink around the steel balls. Ink is a viscous oil, which is prepared by adding linseed oil, synthetic pine nut oil (mainly containing terpene alcohols), mineral oil (oil obtained by fractionating minerals such as petroleum), hard glue and oil smoke. .

2. When using a ballpoint pen, do not write on paper with oil or wax. Otherwise, the oil and wax will embed in the copper bowl along the edge of the steel ball, affecting the ink flow and making it impossible to write. Also avoid If the pen is hit or exposed to the sun, keep the pen cap on when not in use to prevent damage to the pen tip, deformation of the pen barrel, and oil leakage from the pen core, which may cause contamination. In case of cold weather or if it has been left unused for a long time. When the pen does not produce oil, you can soak the pen tip in warm water for a while and then stroke the pen tip on the paper to write.

3. The ballpoint pen has a big shortcoming: the handwriting it writes is very clear at first; but it cannot withstand the test of time. Over time, the handwriting will slowly become blurred. This is because ballpoint pen ink is made from dyes and castor oil. Oil is different from water. It is not easy to dry. Over time, the oil will slowly soak into the paper and the writing will become blurred. Therefore, the ballpoint pen can only be used as an ordinary writing pen. If you want to preserve your handwriting for a long time, you need to use a pen.

4. If the ballpoint pen falls to the ground, if the pen tip hits the ground at 90 degrees, the ballpoint pen tip will not be damaged. However, if the closing area is damaged, "oil leakage" will occur in the gap. In severe cases, The beads may also fall off and make writing difficult.

Usage precautions

The angle is too small

It is easy to wear the closing area of ??the ball seat (the ball seat material is nickel-platinum copper or stainless steel, which is easier to wear than the ball ball) (more), if it comes into contact with the object being written on for a long time, even if the object is paper, the ball seat cannot withstand wear and tear, which may cause the ball to fall off.

Correct Angle

When writing with a ballpoint pen, it is ideal to control the angle between 55° and 70°. At this time, only the ball is in contact with the paper (the ball is very hard and carbonized. Tungsten or ceramic, which is not easy to wear), and the closing area does not contact the writing material, thus ensuring that the ballpoint pen can extend its service life in good writing condition.

The pad paper is too thick

When writing, the pad paper is too thick, and the end of the pen tip contacts the paper, which is easy to wear and loose beads. Recommendation: 0.4 balls cannot be copied; 0.5 balls A maximum of 1 bead can be copied, but not more; a maximum of 0.7 beads can be copied of 3 to 4, but no more. It is best to write at 75° when copying.

Purchasing Points

1. High-end ballpoint pens have obvious trademarks, brand names and model marks on the pen cover, and there are also obvious brand names, production dates and "DA" at the end of the refill. Logo mark (the "DA" mark is the combination of the first letter of the Chinese pinyin of the word "archive").

2. The pen refill must be equipped with a metal oil tube. The pen tip ball must be made of hard alloy - tungsten carbide ball. The writing performance is better than that of ordinary ballpoint pens. The ink poured into the pen refill must be made of hard alloy - tungsten carbide ball. 424 pure blue ink and 322 black ink produced at designated locations. These two inks have the advantages of light fastness, water resistance and impermeability. Ballpoint pen refills filled with these two inks can be used for writing archival documents (including plastic tubing refills, but the color of the tubing must be light yellow tubing).

3. On the packaging of the goods, there are signs and marks such as trademark number, model, manufacturer name, place of origin and quality inspection certificate. Fake and shoddy products. The ink filled in the pen refill is not archival ink approved by the State Archives Administration. There is no "DA" mark on the refill, and there is no trademark, model, factory name, or origin. Some are unbranded pens smuggled in from abroad. The core is assembled and passed off as an imported high-end ballpoint pen.

How to clean ballpoint pen oil on clothes

1. White vinegar cleaning method

Soak the stained area with shampoo, then use a brush dipped in white vinegar to scrub gently .

2. Clean with alcohol and soap

Use a small brush dipped in alcohol to scrub. After the stains have dissolved and spread, soak the clothes in cold water and apply soap to clean them.

3. Clean with toothpaste and a small amount of soap

First soak the stained area with cold water, then apply some toothpaste, apply a small amount of soap and rub it gently.

4. Clean with milk

Boil the milk, put a towel under the clothes, dip a ball of cotton in hot milk and rub it on the oil stain until the oil stain disappears .

5. Other chemical methods

In fact, there are some chemical methods to remove ballpoint pen oil from clothes, such as gently wiping with benzene, carbon tetrachloride or acetone, but these Things are harder to find. Therefore, the methods taught by the editor are easy to operate, and I hope it can bring some convenience to your life.