In business situations, should business people or service personnel wear badges on the left or right? Do you know the etiquette of name labels? I'll tell you next.

Badge wearing etiquette, badges are generally worn on the left chest, and Chinese and foreign customs are mostly the same.

This habit may be due to:

1. Most people are right-handed, so it is more convenient and easier to put the famous brand on the left chest with your right hand.

2. People's hearts are on the left, which may be more easily noticed by others;

In addition, in China:

1. Since ancient times, most people have followed the etiquette habit of "left is top";

2. The reading habit in ancient China was reading from right to left. When you look at others, you should start from your own right and start from the other person's left. It should be easier for others to see the staff badge on their left.

China's early badges were all worn on the left chest, and the 07-style general's dress wore a rank badge on the left chest and a name badge on the right chest.

In foreign countries, there is also etiquette to advocate wearing the breastplate on the right, on the grounds that:

1. When shaking hands, the body on the right side of the person will lean forward slightly, and the name tag will be worn on the right chest to make it easier for the guests to see;

The guest's reading habit is reading from left to right. When you look at others, you should start from your left and start from the other person's right. It should be easier for guests to see the employee's name tag on their right.

Summary:

1. The left and right sides of the badge should be guided by whether the guests can see clearly.

2. If the uniform design is asymmetrical, the badge should be worn on the side that can balance the visual center of gravity.

3. No matter whether the badge is worn on the left or right, all the staff in the same unit or company should be consistent.

The production process of name tag is 1. First of all, the printed-cleaned object is laid flat on the operation panel with the same level for dripping.

2. Take a cup according to the dosage, accurately weigh out 90g of glue A, then weigh out 30g of glue A and glue B, and mix them evenly according to the ratio of 3: 1. Some crystal glue components are 2: 1, others are 1: 1.

3. Take a clean syringe, suck the prepared glue into the syringe, and drop it evenly on the surface of signs, badges, etc. Generally, the thickness of crystal glue layer is 2mm, so it can be leveled naturally.

4. 3-5 minutes after crystal glue drip, observe whether there are bubbles or dust particles on the rubber surface. If there are small bubbles, you can pick them off with a small needle. If you find that the dead corner is not smoothed with crystal glue, you can extradite them with a needle.

5. The poured name plate is cured 10- 14 hours at the room temperature of 20℃-22℃, and hardened into a crystal plate with non-stick surface.

6. If it is an adhesive, trademark, etc. Its thickness is very thin and its boundary is not obvious. It is easy to cause crystal glue overflow when pouring, and it is difficult to reach the thickness of 2mm. Therefore, when making crystal glue, the viscosity should be controlled according to different conditions, and it can be left for 1-2 hours in the smearing process to improve the viscosity and adapt to the perfusion of thin crystal glue.

7. Make a crystal glue name tag with a thickness of over 2mm, and you can drop it twice. After the first drop, cure for 3-5 hours, and then drop another layer.

8. For cleaning after plastic dropping, it is necessary to clean containers made of toluene, xylene and cyclohexanone. If the glue is insoluble in any solvent after hardening, it must be cleaned in machines and containers before hardening. The products made of crystal glue have the advantages of good vision, high transparency and high gloss, and should be widely used in screen printing industry. Note: If the weather is very cold, first heat and dilute the glue A to about 15 degrees.

The use of badges The size of badges is mostly about 2-3CM, including one or more of company name, company LOGO, name, number, position, department, corporate image, etc. You can put it on it. Because the size of the badge board is relatively small, the above contents are abbreviated as much as possible. It is mostly applicable to enterprises, companies, central institutions, public business halls and service windows in all walks of life, without domain restrictions.

Chest number plate is also called badge, number plate, engraved card, work number plate, badge, badge, badge, badge, etc.

A combined name tag with patterns or characters engraved on the surface by laser is characterized in that the base material of the name tag is made by splicing or/and compounding or/and inlaying any one to three materials of bamboo, wood or composite materials. The utility model is formed by splicing, compounding or inlaying base materials of different materials. Designers can match according to the lines, colors and characteristics of different materials to design and produce unique and natural background patterns to highlight and set off the characters and patterns on the name tag, enrich the expression of the name tag and make the name tag more beautiful.