CCC certification is "China Compulsory Certification", its English name is "China Compulsory Certification", and its abbreviation is CCC. The mark of CCC certification is "CCC", which is formulated by the National Certification and Accreditation Administration in accordance with the "Compulsory Product Certification Management Regulations" (Order No. 5 of the General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China).
1. Technical requirements
1.1 All products should be equipped with anti-smash inner headers. See Appendix A for technical requirements.
1.2 Strength requirements must comply with Table 1.
Table 1 (omitted)
1.3 Anti-puncture performance of soles; after puncture test, steel nails shall not penetrate the inner lining.
1.4 The soles should have anti-skid teeth or anti-skid patterns.
1.5 Leather safety shoes worn for thermal processing work must pass heat resistance and flame resistance tests, and must not be deformed.
The burning speed shall not be greater than 1mm/s.
1.6 The overall weight of each pair of shoes shall not exceed 2 kg.
1.7 Other performance requirements are in accordance with the standards issued by the Ministry of Light Industry, seam leather shoes SG27-74, molded leather shoes SG24-74.
２. Test method
2.1 Static pressure test.
2.1.1 Test instrument: The pressure testing machine used has an accuracy of ±1%, the minimum scale value is below 5kg
and the measurement range shall not be less than 2,000kg. The area diameter of the test platform should be greater than 75mm, and the upper and lower platforms should be parallel.
2.1.2 Sample preparation: Extend the rear edge of the inner toe cap of the product backwards by 25±3mm beyond the shoe upper and lining
and cut off the remaining parts. , leaving only the toe and sole as specimens. The schematic diagram of the specimen is shown in Figure 1.
2.1.3 Test method: Place a plasticine cylinder of the same height and 22mm diameter
in the highest part of the head of the sample, and place the plasticine part in the sample Place it in the center of the pressure test platform. Slowly pressurize at a rate of 3-5 minutes
When the pressure reaches 1,400kgf, stop the machine for 1 minute and then return the pressure to zero:
Take out the plasticine and measure its height . It is qualified when ≥15mm.
2.2 Impact test:
2.2.1 The instrument structure of the impact test is shown in Figure 2.
2.2.2 Sample preparation: Same as 2.1.2.
2.2.3 Test method: The weight of the testing machine weight is 23±0.2kg. Fix the pattern
on the device and adjust the weight drop height according to Table 1. Then let the weight drop freely to conduct the impact test. After the test
take out the plasticine and measure its size. If it is ≥15mm, it is qualified.
2.3 Puncture test of anti-smash shoes: Use No. 60 (standard GB346-75) steel nails, place them
on the press platform, and fix them upright with plasticine. Place it on the center of the forefoot of the sole and slowly apply pressure. When the pressure reaches 50kgf, stop the machine for inspection.
2.4 Heat resistance test: Place the sample in an oven at 100±5℃, bake for 20 minutes,
cool to normal temperature and then inspect. There must be no deformation or drying.
2.5 Flame resistance test: Cut the upper of the sample into 150×13mm strips, clamp them on the fixture of the dripping table, and align them with the horizontal direction. into an angle of 45°. Then use an alcohol lamp to burn the lower end, measure the time it takes for the flame to spread to the center, and calculate its burning speed. The number of samples is three, and the average speed is taken as the burning speed.
Figure 2 (omitted)
3. Inspection rules
3.1 Products must be identified by the technical department designated by the state, meet the requirements of this standard and obtain a certificate of conformity
before they can be produced and sold.
3.2 Products can only leave the factory after passing the inspection by the manufacturer in accordance with this standard, and have a product certificate and a supervision certificate issued by the technical appraisal department.
3.3 Products should be visually inspected one by one, and other products should be in accordance with standards.
Taking 1,000 pairs as a batch,
2‰ random sampling, if one of the static pressure and impact tests fails, double the sampling and re-inspection.
If still If there is one item that is unqualified, double the sampling for re-inspection. If there is still one item that is unqualified, this batch of products will be deemed unqualified.
4. Marking transportation and storage
4.1 Each pair of shoes should have the following markings: manufacturer name (or) trademark, unified shoe number, product grade,
Supervision certificate, certificate of conformity , production year, month, day.
4.2 The outer packaging should have the following signs: manufacturer name (or trademark), product name, specifications,
Quantity, grade, item number, box number, gross weight, packaging box date.
4.3 Avoid exposure to the sun, rain and moisture during transportation and storage. Do not keep it together with acids, alkalis, oils and corrosive items. The storage warehouse should be kept ventilated and dry, and the product should be stored at a distance of more than 200mm from the floor and walls.
Appendix A: Anti-smash inner toe caps of leather safety shoes
Anti-smash inner toe caps are the main component of leather safety shoes. It is a professionally produced product. If the product can
p>
Meeting the standard requirements ensures the anti-smash performance of leather safety shoes.
A1 technical requirements
The dimensions of A1.1 products are shown in Figure 1. The horizontal distance a from the tip of the inner toe to the rear edge is 40-
60mm; the height b is more than 35mm; the lower edge is rolled horizontally and the width c of the roll-in should be 3m
ｍ or above.
A1.2 Appearance quality requirements: The surface should be smooth, and the edges and corners should be arc-shaped. Steel products must be
antirust treated.
A1.3 The static pressure and impact test methods are the same as the standard requirements for leather safety shoes, but the sample does not need to be prepared, and the test is conducted directly
with the anti-smash inner toe cap. The gap height after the test is ≥22mm as qualified product.
A2 Others
A2.1 Inspection rules: 1,000 pieces are a batch, except for random sampling of 4‰, other standards are the same as before
Require.
A2.2 Marking, transportation and storage are the same as the previous standards.